How to Check a Used Car With an OBD-II Scanner Before You Buy
Use an OBD-II scanner on a used car: readiness monitors, cleared-code tells, pending and permanent codes, freeze frame, Mode 6 and German turbo checks.
10 minBy Haris Cars

Contents · 11 sections
- 01What a generic OBD-II scanner can and can't see
- 02Step 1: Check the warning lamp before you plug in
- 03Step 2: Read the readiness monitors
- 04Step 3: Read stored, pending and permanent codes
- 05Step 4: Read the freeze-frame data
- 06Step 5: Look at Mode 6
- 07What to look for on turbocharged German engines
- 08When you need a brand-specific tool
- 09US inspection and emissions context
- 10Frequently asked questions
- 11Sources
To check a used car with an OBD-II scanner, plug it into the diagnostic port and read five things: stored, pending and permanent fault codes, the readiness monitors, the distance driven since codes were last cleared, any freeze-frame data, and the Mode 6 test results. "Not ready" monitors combined with only a few miles since the last clear usually mean someone wiped the codes shortly before the sale. On a German car, follow up with a brand-specific tool, because a generic reader only sees the emissions side of the engine computer.
A scan is one part of an inspection, not a replacement for it. Pair it with a careful visual inspection, a cold start and a test drive.
What a generic OBD-II scanner can and can't see
A generic OBD-II scanner reads the standardized, emissions-related diagnostics that US inspection programs test on gasoline cars from the 1996 model year on. It does not read the manufacturer's own fault memory for the rest of the car.
The standard data comes from the SAE J1979 protocol. California's OBD II regulation (13 CCR 1968.2) spells out what the port has to report, and it is written around emissions monitoring. BMW, VW, Audi and Mercedes all store far more detail in their own formats. BMW's service bulletins quote engine faults like 120308 (boost pressure control, plausibility: pressure too low) and diesel faults like 245700. Mercedes uses its XENTRY system and VW uses its own adaptation channels. Those live in the manufacturer layer, which is why the second half of this guide covers brand tools.
Step 1: Check the warning lamp before you plug in
With the ignition on and the engine off, the check engine light (MIL) should come on. It should then go out once the engine starts.
This is the bulb check US inspection stations use. Under the federal inspection rule (40 CFR 85.2222), a car fails if the MIL doesn't light at all with the key on and engine off, even with no codes stored. A dead lamp on a used car is a red flag: it is one way to hide a fault. The UK MOT does the same visual check, as a Major defect, on gasoline cars first used from July 2003 and diesels from July 2008.
Step 2: Read the readiness monitors
Readiness monitors are the car's self-tests for emissions systems such as the catalyst, oxygen sensors, evaporative (EVAP) system and EGR. Each one reports "complete" or "not complete" since the fault memory was last cleared.
California's OBD II rule requires every monitor to drop to "not complete" whenever fault memory is cleared, while a normal key-off must not reset it. That is why a row of "not ready" monitors is the classic sign of recently cleared codes. New York's DMV lists the innocent explanations too: a recent repair where codes were cleared, a disconnected or replaced battery, or a software update.
Some details matter when reading the screen:
- Ignore the continuous monitors: under California's rule, the gasoline misfire and comprehensive component monitors always show "complete", and Smog Check ignores misfire, fuel and comprehensive component on gasoline cars. They tell you nothing about recent clearing.
- Look at "distance since codes cleared": on 2005 and newer cars using the CAN protocol, the regulation requires the computer to report distance traveled and warm-up cycles since fault memory was last cleared. If that reads 30 miles on a car the seller says hasn't been touched in months, ask why.
- One incomplete monitor isn't proof of anything: the EVAP monitor in particular needs specific conditions. California's Smog Check allows 2000 and newer gasoline cars to pass with only the EVAP monitor incomplete.
If monitors are incomplete, ask the seller to drive the car until they set, then re-scan. NY DMV's generic drive cycle includes a cold start, idling, steady 55 mph cruising and coast-downs. It notes that two cycles with a cool-down between them are usually needed.
Step 3: Read stored, pending and permanent codes
Stored (confirmed) codes are faults the computer has verified. Pending codes are faults seen once but not yet confirmed. Permanent codes are confirmed faults that a scan tool can't erase.
- Stored codes: what most cheap readers show first (Mode $03). A code can be stored without the lamp on. The federal inspection rule passes a car if the MIL isn't commanded on, "even if DTCs are present".
- Pending codes: available on 2005 and newer cars through Mode $07, per California's regulation. NY DMV describes this as a problem that hasn't yet turned on the check engine light. If a fault survives a code clear, it can show up here before the light comes back on, so a reader that shows pending codes is worth having.
- Permanent codes: on 2010 and newer vehicles that support them, California's Bureau of Automotive Repair (BAR) says they can't be cleared with a scan tool or by disconnecting the battery. They only clear after the fault is fixed and the related monitor runs and passes. A permanent code with no stored code means someone cleared a real fault and the car hasn't yet proved it's fixed.
Step 4: Read the freeze-frame data
Freeze frame is a snapshot of engine data saved at the moment a fault code was stored. It shows the conditions the car was in when the problem happened.
The regulation requires the freeze frame to include the code that triggered it and a set of key engine signals, and it gives misfire and fuel-system faults priority over other codes. Audi tells its dealers to use this data: if a misfire code was set during a cold start, look for cold-start bulletins rather than replacing ignition coils.
For a buyer, the freeze frame answers a simple question: did the fault happen under hard load on the highway, or idling cold in a driveway?
Step 5: Look at Mode 6
Mode 6 (Service $06) shows the results of the most recent run of each non-continuous self-test, alongside the minimum and maximum limits the result has to fall within.
California's regulation requires those results and limits to be reported. For 2005 and newer cars, it also requires misfire monitor results in the standardized format. Newer cars built to the SAE J1979-2 standard must also report cylinder-specific misfire counts in their live data. A result that passes, but sits near its limit, can point to a part that is starting to fail before any code is set. Not every reader decodes Mode 6 into plain English, and not every car reports it clearly. Treat it as extra evidence, not a verdict.
What to look for on turbocharged German engines
On BMW, VW, Audi and Mercedes turbo engines, the three most telling data points are misfire counts, fuel trims and boost-related faults.
Misfires
P0300 is "Random/Multiple Cylinder Misfire Detected", and P0301 to P0306 name the cylinder. That's how Audi's misfire bulletin defines them. VW's own guidance to dealers says a cylinder-specific code should accompany a genuine misfiring cylinder. If one cylinder shows misfire counts in Mode 6 or a brand tool while the others read zero, that cylinder needs a closer look: coil, plug, injector or compression. For engine-specific codes on the 2.0T, see our EA888 check-engine light guide.
Fuel trims
Fuel trim is the percentage the engine computer adds to or subtracts from its base fueling to hold the right air-fuel ratio. A positive number means it's adding fuel to correct a lean condition. A negative number means it's taking fuel away because the mixture is rich. A Vehicle Service Pros technical article gives the modern rule of thumb as total trim (short-term plus long-term) within about ±5%, down from the older ±10%.
Watch the trims at idle, then at a steady 2,500 rpm or so. A vacuum or boost leak shows as strongly positive trims at idle that move back toward normal as airflow rises. BMW's N55 bulletin uses the same logic: positive adaptation values point to a lean condition, and the next step is a smoke test of the intake.
Boost faults and signs of tuning
- Generic underboost code: Audi's bulletin for 2005-2007 A3 and A4 2.0 TFSI models lists
P0299(Turbo/Super Charger Underboost). The cause it gives is a torn membrane in the turbocharger recirculation valve, N249. - BMW boost codes: on the N55, BMW's bulletin covers faults
120308and2C57, "boost pressure control, plausibility: pressure too low", with the engine in reduced-power failsafe. These are BMW's own fault codes, so read them with a BMW-capable tool. - Tuning: the same BMW bulletin lists aftermarket intakes, blow-off valves, exhausts, performance catalysts, "piggy back modules" and tuner software as possible causes of boost faults.
A generic scanner can also read the engine software's calibration ID (CAL ID) and calibration verification number (CVN). California requires a CVN on 2005 and newer cars so that changes to the emission-related software can be detected. Write both down. A specialist with reference data can use them to spot non-factory engine software. For known boost-path weak spots, our N55 common problems guide is a good companion.
When you need a brand-specific tool
Use a brand-specific tool when the generic scan is clean but you want the full picture. That means every module, the manufacturer's own fault codes and the service functions.
The dealer tools are BMW's ISTA and Mercedes' XENTRY, both named in the service bulletins we cite. Enthusiast-level equivalents include VW/Audi interface software in the VCDS or OBDeleven mold, and BMW-specific apps and interfaces. These talk to the manufacturer's own diagnostic layer: they can show manufacturer fault codes and text, and run service functions such as adaptations and DPF regenerations. The Ross-Tech wiki, for example, documents these procedures for VCDS. The service bulletins we quote show the difference. BMW's diesel bulletins refer to DPF faults and a "distance since last regeneration" counter in the DDE, Mercedes' bulletins refer to DPF fill level and regeneration history in XENTRY, and VW's tech tips use adaptation channels inside the engine module. None of that is visible on a basic reader.
A good independent specialist will have one of these tools. Paying for a full scan before you buy is cheap insurance, especially on a diesel or a car with a modified engine. The channel's video guides show what to look for on the engines themselves.
US inspection and emissions context
US inspection programs test cars through the same port, so a car that can't pass one is a problem you'd be buying.
- Federal rule: under 40 CFR 85.2222, the inspection reads readiness (Mode $01, PID $01) and, if the MIL is commanded on, the stored codes (Mode $03). A commanded-on MIL is a fail. Model year 1996-2000 cars may pass with up to two unset monitors, and 2001 and newer with one. A car with an unset monitor and a code that turns the MIL on fails.
- California: BAR's Smog Check reference allows 2000 and newer gasoline cars only an incomplete EVAP monitor, and 2007 and newer diesels any two. Since July 1, 2019, permanent codes count toward the result.
- New York: the DMV OBD-tests gasoline vehicles from 1996 and most diesels from 1997 with a GVWR under 8,501 lb.
Rules vary by state and county, so check your local program before buying a car that shows incomplete monitors.
Frequently asked questions
Can a seller hide problems by clearing the codes?
For a while. Clearing resets the readiness monitors to "not complete", and newer cars also report distance and warm-up cycles since the clear. On 2010 and newer cars that support permanent codes, a confirmed fault stays stored until the monitor proves the repair.
How long does it take for readiness monitors to set?
It depends on the car and the monitor. NY DMV says two drive cycles with a cool-down in between are usually needed, and some monitors, like EVAP, need specific conditions. Ask the seller to drive the car normally for a few days, then re-scan.
Is a cheap Bluetooth OBD-II reader good enough?
For the basics, yes, if it shows readiness, pending codes, freeze frame and distance since codes were cleared. For a German car, add a brand-specific scan, because the generic protocol doesn't cover the manufacturer's own fault memory.
Does a clean scan mean the car is fine?
No. OBD-II watches emissions-related systems. It won't tell you about worn suspension, oil leaks or a timing chain that's starting to rattle. Combine the scan with a full inspection and a test drive.
Sources
- eCFR: 40 CFR 85.2222, Onboard diagnostic test procedures
- California Air Resources Board: OBD II regulation, 13 CCR 1968.2 (2021 amendments)
- California Bureau of Automotive Repair: Permanent Diagnostic Trouble Codes
- California Bureau of Automotive Repair: On-Board Diagnostic Test Reference
- New York DMV: What do you mean my car's not ready?
- GOV.UK: MOT inspection manual, section 8
- Audi of America (via NHTSA): TSB 2033630, MIL on with P0300-P0304
- Volkswagen of America (via NHTSA): TSB 2032174, misfire and injector replacement
- Audi of America (via NHTSA): TSB 2013060, MIL on with P0299
- BMW (via NHTSA): SI B12 16 11 (August 2011), N55 boost pressure control fault
- BMW (via NHTSA): SI B12 16 11, N55 boost pressure control fault
- BMW (via NHTSA): SI B18 03 10, No regeneration of the DPF
- Mercedes-Benz (via NHTSA): LI49.20-N-080011, OM654 DPF fill level
- Volkswagen of America (via NHTSA): Tech Tip 26-19-01TT
- Ross-Tech Wiki: Diesel Particle Filter Emergency Regeneration
- Vehicle Service Pros: Fuel Trim, Finding a Vacuum Leak Using Fuel Trim Data
Keep reading
Related posts

Owner Guides
BMW LL-01 vs LL-04 vs LL-17 FE+: Which Oil Does Your BMW Need?
BMW Longlife oils decoded: what LL-01, LL-04, LL-12 FE, LL-14 FE+, LL-17 FE+ and LL-19 FE mean, which engines take which, and US vs EU rules.
BMW8 min

Maintenance & Problems
Timing Chain or Belt? BMW, VW, Audi and Mercedes Engines
Which BMW, VW, Audi and Mercedes engines use a timing chain or belt, verified belt intervals for EA211 and 1.9 TDI, and the warning signs of chain wear.
10 min

Maintenance & Problems
DPF Regeneration Explained: TDI, B47/N47, OM651 and OM654
How DPF regeneration works on VW/Audi TDI, BMW N47/B47 and Mercedes OM651/OM654: warning lights, oil dilution, forced regens, cleaning and delete law.
10 min

Maintenance & Problems
EA888 Gen 1/Gen 2 Timing Chain Tensioner Failure and Settlement
Which VW and Audi 2.0T engines had timing chain tensioner failures, how they fail, what the US settlement covered, and what to check on an older 2.0T today.
8 min

Engine Guides
VW/Audi EA888 Engine Guide: Gen 1 to Gen 4 Explained
EA888 Gen 1 to Gen 4: verified specs, what changed, tensioner, oil consumption and water pump problems, settlements, and a used-buyer checklist.
13 minVideo

Engine Guides
BMW N55 Engine Guide: Specs, Problems and Buying Advice
BMW N55 3.0 turbo six explained: verified specs by model, the VANOS recall, common leaks and water pump faults, N54 differences and a used-car checklist.
BMW11 min

Lights on.
Subscribe.
Engine walkthroughs for BMW, VW, Audi and Mercedes-Benz owners, on YouTube at @HarisCars.
Subscribe on YouTube