Maintenance & Problems · BMW
Timing Chain or Belt? BMW, VW, Audi and Mercedes Engines
Which BMW, VW, Audi and Mercedes engines use a timing chain or belt, verified belt intervals for EA211 and 1.9 TDI, and the warning signs of chain wear.
10 minBy Haris Cars

Contents · 9 sections
- 01BMW: every engine on this list uses a chain
- 02Volkswagen and Audi: chains on the big engines, belts on the small ones
- 03Mercedes-Benz: chains throughout, several at the back
- 04Belt intervals we could verify
- 05Chains do not have a replacement interval, but they do wear
- 06Warning signs of timing chain wear
- 07What this means when you buy
- 08Frequently asked questions
- 09Sources
Almost every BMW, Audi and Mercedes engine we cover uses a timing chain. The belt-driven exceptions are all Volkswagen Group designs: the EA211 TSI petrol family, the EA288 2.0 TDI and the older 1.9 TDI Pumpe-Düse. Chains have no fixed replacement interval but do wear out. Belts have a schedule, and that schedule varies by engine code, model year and market.
Below is the engine-by-engine list, followed by the belt intervals we could verify and the warning signs that a chain is stretching. Where we could not confirm an interval for a specific engine and market, we say so. In those cases the service schedule for your VIN is the only answer to trust.
BMW: every engine on this list uses a chain
BMW has not used a cam belt on any of these engines, so the questions are where the chain sits and how hard it is to reach.
- M54 (inline-six): chain. BMW's main (lower) chain runs from the crankshaft to the exhaust camshaft gear.
- N52 (inline-six): chain. BMW's repair instruction for replacing it starts with removing the cylinder head cover, spark plugs and vibration damper.
- N54: chain. BMW publishes a dedicated chain replacement procedure.
- N55: chain. Genuine BMW chain kits are listed for the N52, N55 and S55.
- N20 (2.0 turbo four): chain at the front, on the accessory-drive side. A second chain drives the oil pump. That oil pump chain drive is the subject of BMW's warranty extension (see below).
- N47 (2.0 diesel): chain at the gearbox end. BMW's repair instruction for replacing both chains lists removing the engine as the first preliminary step.
- B38, B48 and B58 (modular petrol 3, 4 and 6-cylinder): chain on the transmission side. BMW's B58 training manual says the chain drive was placed there because the transmission's inertia damps rotary vibration and reduces chain loads. Later TU versions of the B46/B48 and B58 switched from a two-part chain to a one-piece chain.
- B47 (2.0 diesel): chain. BMW's B46 training material describes the petrol modular engines' two-part chain drive as using synergy parts with the diesel engines.
- S55 (F8x M2/M3/M4): chain.
- S58 (G8x M2/M3/M4, X3 M/X4 M): chain.
The rear-mounted chains on the N47, the B-series and the diesels are the ones that make repairs expensive, because the gearbox or the whole engine has to come out. Our B47 vs N47 comparison covers how the diesel chain story changed between generations.
The N20 chain warranty extension
BMW of North America's bulletin SI B11 03 17 (October 2017) extended coverage on the N20 and N26 timing chain and oil pump drive chain to 7 years/70,000 miles from the original in-service date. It covered US-spec cars with engines built in windows running up to February 2015. The symptom BMW described was a whining noise from the lower engine, near the oil pump, that rises in pitch with rpm. The cause was wear on the oil pump chain drive sprockets. Given the 7-year limit, most if not all eligible cars have now aged out of it. Our N20 and N26 problems guide covers the rest of that engine.
Volkswagen and Audi: chains on the big engines, belts on the small ones
VW Group splits by engine family: the EA888 and the Audi V6 and five-cylinder engines use chains, while the EA211, EA288 and 1.9 TDI PD use a toothed belt.
- EA888 (1.8/2.0 TSI and TFSI): chain. Early chain tensioner failures led to US class action litigation. The Opheim settlement covers 2012 to 2015 Audi A4, A5 and Q5 models with the second-generation EA888. It extends coverage of tensioner and chain failures to 10 years or 100,000 miles from the in-service date, and the court approved it in August 2024.
- EA211 (1.0, 1.2, 1.4 and 1.5 TSI): toothed belt. Gates, which supplies belt kits for this engine, advises changing the water pump at the same time as the belt.
- EA288 (2.0 TDI): toothed belt. Belt and water-pump kits are listed for EA288 codes such as CXGA and CXGB in the VW T6.
- 1.9 TDI Pumpe-Düse: toothed belt.
- EA837 3.0 TFSI (supercharged V6): chains. Audi's repair manual lists "gearbox removed" as a prerequisite for replacing the valve-gear drive chain, which tells you which end of the engine it sits on.
- EA839 2.9/3.0 TFSI (turbo V6): chains. The workshop manual has separate sections for the camshaft timing chains and the oil pump drive chain.
- EA855 2.5 TFSI five-cylinder, including the DAZA evo: chains. Aftermarket chain kits list CEPA, CZGB, DAZA and DNWA engine codes.
Mercedes-Benz: chains throughout, several at the back
Every Mercedes engine here uses a chain, and on the newer designs it sits at the transmission end.
- M274 (turbo four): a conventional timing chain drives both camshafts. The oil pump runs on a separate chain from the crankshaft.
- M264/M260 (1.5/2.0 turbo four): timing chain, with hydraulic cam adjusters on both camshafts.
- M254 (turbo four with integrated starter-alternator): timing chain at the rear of the engine. Mercedes' StarTuned service magazine notes that deep chain repairs mean pulling the engine.
- M177/M178 (AMG V8): chain drive with a secondary chain. A 2018 Mercedes bulletin (LI05.10-P-068624) traced a cold-idle squeak or tick to the secondary chain drive's tensioning rails.
- OM651 (four-cylinder diesel): chain. See the OM651 bulletin in the warning-signs section below.
- OM654 (four-cylinder diesel): chain on the gearbox side, which auto motor und sport says makes replacement more involved.
- OM606 (diesel): double-row chain that drives the camshafts and the injection pump.
Belt intervals we could verify
VW Group belt intervals have changed several times and differ by market, so treat any single number online with suspicion. These are the figures we could tie to a specific engine and source.
- EA211 TSI, UK, 2020-on Skoda Octavia (1.0 TSI, 1.5 TSI, 1.5 eTSI): Haynes' maintenance plan lists "no recommended period" for timing belt renewal.
- EA211 1.0, Brazil: Volkswagen do Brasil specifies replacement at 120,000 km or 4.5 years in normal use. Under severe use the figure halves to 60,000 km or 2.5 years, and VW requires new camshaft pulley bolts because they are torque-to-angle fasteners.
- 2.0 TDI, UK, 2020-on Skoda Octavia: Haynes lists timing belt renewal every 210,000 km.
- 1.9 TDI PD, Europe (Gates bulletin, 2007): the Golf IV with engine code AJM was 60,000 km up to model year 2000 and 90,000 km from 2001. Codes ARL, ASZ, ATD and AXR moved from 90,000 km to 120,000 km for 2004-on cars. The Golf V 1.9 TDI (including BKC and BLS) was 120,000 km.
Two lessons from that list. The same EA211 engine family gets "no fixed period" in one market and 120,000 km in another. And the 1.9 TDI's interval doubled over a few model years. Gates also notes that prolonged exposure to temperatures above 26°C or below -6°C cut the time limit on VAG belts from 5 to 4 years under the OE guidance it summarized. If your car's schedule shows a time limit, honor it even at low mileage.
For every other belt engine and market, check the service schedule for your VIN. Change the tensioner and idlers with the belt, and on the EA211 the water pump as well.
Chains do not have a replacement interval, but they do wear
None of the manufacturer documents we reviewed give a mileage for replacing a timing chain. Chains are replaced on condition. Mercedes' StarTuned magazine says that in a properly maintained vehicle, chains and related hardware can last well over 200,000 miles.
What shortens that life is wear in the pins and rollers, which lengthens the chain, plus guides and tensioners that depend on oil pressure and oil quality. Hydraulic tensioners take a moment to pressurize after a cold start, which is why the classic symptom of a worn chain is a brief rattle at start-up.
Warning signs of timing chain wear
The most common sign is a rattle for a few seconds after a cold start that goes away once oil pressure builds. The other signs below come from manufacturer bulletins and specialist workshop guidance.
- Start-up rattle: Mercedes' OM651 bulletin (LI05.10-N-057796) describes rattling or knocking from the chain drive about 2 to 5 seconds after start, caused by a stretched chain, possibly due to the tensioner.
- A whine that rises with rpm: BMW's N20 bulletin describes this from the lower engine near the oil pump, caused by worn oil pump chain sprockets.
- Cold-idle ticking or squeaking: Mercedes linked this on the M177/M178 to the secondary chain drive's tensioning rails. It was most obvious below 80°C coolant temperature.
- Cam/crank correlation fault codes: a stretched chain shifts cam timing relative to the crankshaft, and the engine computer may store correlation faults. Codes that return immediately after clearing deserve a proper timing check.
- Metal in the oil or filter: chain and guide debris can show up at an oil change, though it needs wider diagnosis to confirm where it came from.
- Rough running, harder starting or lost power: these show up later. Many other faults cause them too.
Diagnose before you replace. Mercedes' StarTuned magazine notes that camshaft adjusters can rattle at start-up and mimic a worn chain. Measure the stretch rather than guessing. Mercedes' OM651 procedure uses a measuring chain tensioner: up to 250,000 km, a reading below 82 mm on its scale calls for a new tensioner only, and a reading above that calls for a new chain. On BMW and VW engines, a workshop will check cam timing against the crank with locking tools or live data.
What this means when you buy
Belt engines carry a known, scheduled cost. Chain engines carry an unscheduled one, and it is much larger when the chain sits at the gearbox end. On a used N47, B-series BMW, M254, OM651, OM654 or Audi V6, listen to a fully cold start, with the car sitting overnight, before you buy. Ask for oil-change records, because missed or overextended oil changes hit chains and tensioners first. On an EA211, EA288 or 1.9 TDI, ask for the invoice for the last belt change and check it against the age limit as well as the mileage. Our pre-purchase checklist for turbo cars covers the rest of the inspection, and the video guides show what several of these engines sound like.
Frequently asked questions
Does the BMW B48 have a timing belt or chain?
A chain. On the B38, B48 and B58, BMW put the chain drive at the transmission end of the engine, and later TU versions use a one-piece chain instead of the original two-part layout.
Do VW TSI engines have a timing belt?
It depends on the family. EA211 engines (1.0, 1.2, 1.4 and 1.5 TSI) use a toothed belt. EA888 engines (1.8 and 2.0 TSI) use a chain.
When should I change the timing belt on a VW 1.0 or 1.5 TSI?
Check the service schedule for your VIN. Published guidance differs by market: Haynes lists no fixed period for UK Skoda Octavia EA211 engines, while VW Brazil specifies 120,000 km or 4.5 years for the EA211 1.0, halved for severe use.
How long does a timing chain last?
There is no factory replacement interval on these engines. Chains are replaced on condition, and Mercedes says a well-maintained chain can last well over 200,000 miles. Oil quality and change intervals have the biggest influence.
Do any Mercedes engines use a timing belt?
None of the Mercedes engines on this list do. The M274, M264, M254, M177/M178, OM651, OM654 and OM606 all use chains.
Sources
- BMW Group technical training: B58 Engine (ST1505)
- BMW Group technical training: B46 Engine (ST1508)
- BMW Group technical training: N20 Engine (ST1111)
- BMW Group technical training: N55 Engine (ST501)
- NHTSA: BMW SI B11 03 17, N20 and N26 timing chain and oil pump drive chain warranty extension
- BMW repair instructions: Replacing timing chain (N52)
- BMW repair instructions: Replacing timing chain (N54)
- BMW repair instructions: Replacing both timing chains (N47/M47)
- BimmerWorld: Lower timing chain, M50/M52/M54 (BMW 11311432176)
- BimmerWorld: Timing chain kit, N51/N52/N55/S55
- BimmerWorld: Timing chain, S58
- BimmerWorld: BMW B46TU and B58TU differences
- PowerUP Szczecin: BMW N20 vs B48 differences and timing chain
- PowerUP Szczecin: BMW N47 and B47 timing chains, symptoms and replacement
- Kessler Topaz Meltzer & Check: Volkswagen Timing Chain II (Opheim v. Volkswagen)
- PMM: Replacing the timing belt on an EA211 engine (Gates)
- Haynes: Skoda Octavia IV 2020-2025 maintenance plans
- O Mecânico: EA211 timing belt has extended service life
- Gates Technical Bulletin 020: VAG timing system replacement intervals
- BAR-TEK: 2.0 TDI T5/T6 timing belt kit and water pump (EA288 fitment)
- Audi workshop manual: 3.0 TFSI supercharged, removing and installing drive chain for valve gear
- Audi workshop manual contents: 2.9/3.0 TFSI EA839 (Kfz-Verlag)
- Audi workshop manual: 2.5 TFSI five-cylinder chain drive
- BAR-TEK: 2.5 TFSI timing chain kit (CEPA, CZGB, DAZA, DNWA)
- Mercedes-Benz StarTuned: M274 Tour, Tips and Tricks (September 2021)
- Mercedes-Benz StarTuned: M264/M260 engine and M254 introduction (Summer 2022)
- Mercedes-Benz StarTuned: Timing Chain Tensioners (June 2020)
- Mercedes-Benz StarTuned: A Question of Timing
- NHTSA: Mercedes LI05.10-N-057796, OM651 engine noise (rattling) after engine start
- NHTSA: Mercedes LI05.10-P-068624, M177/M178 erratic noise from front of engine
- auto motor und sport: Everything you need to know about the Mercedes OM654 diesel
- Wikipedia: Mercedes-Benz OM606 engine
Keep reading
Related posts

Maintenance & Problems
DPF Regeneration Explained: TDI, B47/N47, OM651 and OM654
How DPF regeneration works on VW/Audi TDI, BMW N47/B47 and Mercedes OM651/OM654: warning lights, oil dilution, forced regens, cleaning and delete law.
10 min

Maintenance & Problems
EA888 Gen 1/Gen 2 Timing Chain Tensioner Failure and Settlement
Which VW and Audi 2.0T engines had timing chain tensioner failures, how they fail, what the US settlement covered, and what to check on an older 2.0T today.
8 min

Engine Guides
VW/Audi EA888 Engine Guide: Gen 1 to Gen 4 Explained
EA888 Gen 1 to Gen 4: verified specs, what changed, tensioner, oil consumption and water pump problems, settlements, and a used-buyer checklist.
13 minVideo

Cars
VW EA888 Carbon Buildup: What Owners Need to Know
Learn why VW EA888 carbon buildup happens, the symptoms to watch for, when walnut blasting makes sense, and why it is not a fixed service for every owner.
10 minVideo

Engine Guides
VW 1.9 TDI Engine Guide: VE vs PD, Codes and Problems
VW 1.9 TDI explained: VE vs Pumpe-Düse, verified engine codes (ALH, BEW, BRM and more), timing belt intervals, PD cam wear and a buyer's checklist.
Volkswagen11 minVideo

Engine Guides
BMW N20 and N26 Engine Guide: Specs, Chain Issue, Buying
BMW N20/N26 specs by version, the timing and oil pump chain problem with BMW's 7/70 extension and Gelis settlement, recalls, and a used-car checklist.
BMW13 minVideo

Lights on.
Subscribe.
Engine walkthroughs for BMW, VW, Audi and Mercedes-Benz owners, on YouTube at @HarisCars.
Subscribe on YouTube