Skip to content

Engine Guides · BMW

BMW N47 Diesel Guide: Timing Chain, Recalls and Buying

BMW N47 2.0 diesel: specs by model, which engines the timing chain campaign covered, N47 vs N47T, EGR and fuel pump recalls, and a used-car checklist.

12 minVideo walkthroughBy Haris Cars

Video walkthrough of this post.Open on YouTube

The BMW N47 is a 2.0-liter four-cylinder common-rail turbodiesel that BMW introduced in March 2007 and fitted to most of its four-cylinder diesel models until the B47 replaced it. It is strong and economical, but its timing chain sits at the gearbox end of the engine, and chain wear on early engines is the problem it is known for. Buy a later, well-serviced car, or an early one with proof the chain work has been done, and check the EGR cooler recall status before you sign.

Haris walks through the engine in the video above. This guide is the written reference, with a source for every spec, campaign and recall we cite.

N47 at a glance

The N47 is a 1,995 cc inline-four diesel with four valves per cylinder, common-rail injection and a chain-driven valvetrain at the rear of the block.

  • Layout: inline four-cylinder, four valves per cylinder, turbodiesel.
  • Displacement: 1,995 cc.
  • Bore × stroke: 84 × 90 mm, per BMW's workshop technical data for the N47/N47S D20.
  • Compression ratio: 16.0:1 in that same BMW data (December 2007 issue).
  • Injection: common rail. On the later N47TU, BMW lists Bosch CRI2.5 solenoid injectors at up to 1,800 bar, fed by a single-piston Bosch CP4.1 high-pressure pump.
  • Induction: single turbo on most versions. The N47TU uses a variable nozzle turbine (VNT). The 123d version has two turbos, which ADAC lists as "Bi-Turbo".
  • Block: aluminum alloy with cast-iron cylinder liners, according to UnixNerd's engine reference. We could not find a BMW document for the N47 block material that we could open, so treat this line as secondary.
  • Timing drive: chain, at the flywheel (gearbox) end of the engine.
  • Emissions hardware: exhaust gas recirculation (EGR) and a diesel particulate filter (DPF).
  • Years: from March 2007, replaced by the B47 in the mid-2010s.

Power and torque vary by model. Published figures from ADAC's model catalogue and BMW's US launch information:

  • 118d (E87, 2007): 105 kW (143 PS) at 4,000 rpm, 300 Nm at 2,000 rpm (ADAC).
  • 120d (E87, 10/2007 to 09/2008): 130 kW (177 PS) at 4,000 rpm, 350 Nm at 2,000 rpm (ADAC).
  • 123d (E87, 10/2007 to 02/2009): 150 kW (204 PS) at 4,400 rpm, 400 Nm at 2,000 rpm, twin turbo (ADAC).
  • 320d (F30, 02/2012 to 01/2015): 135 kW (184 PS) at 4,000 rpm, 380 Nm at 1,750 rpm (ADAC).
  • 328d (F30, US market, from 2014 model year): 180 hp and 280 lb-ft from 1,750 rpm, with an eight-speed automatic (Automotive Fleet).

Where you'll find the N47

The N47 powered BMW's four-cylinder diesels across the 1, 3, 5 Series and X range in Europe from 2007, and the 328d and X3 xDrive28d in the US.

  • Early engines (2007 to 2008 build): 118d, 120d and 123d in the E81/E82/E87/E88 1 Series; 318d and 320d in the E90/E91/E92/E93 3 Series; 520d in the E60/E61 5 Series; and the E83 X3. These are the models named in BMW's 2015 timing chain campaign, reported by L'argus.
  • Later European cars: the F30 320d (ADAC lists the N47D20C from 2012). Published application lists also include four-cylinder diesels in the F10 5 Series, F20 1 Series and E84 X1.
  • US market: BMW's US service bulletin SI B18 03 10 lists the F30/F31 328d and F25 X3 xDrive28d under the N47T/N57T engines. NHTSA recall records cover the 328d from the 2013 to 2018 model years and the X3 xDrive28d from 2015 to 2017.

Not sure which diesel your car has? The engine code is stamped on the block and shows in the VIN decode. Our guide to finding your exact engine code shows where to look.

Versions and revisions: N47 vs N47T

The N47 was revised several times. The changes that matter most are the early crankshaft and chain updates and the second-generation N47T (also written N47TU).

First generation, 2007 to 2008

The original N47 arrived in March 2007 in the facelifted 1 Series. These are the engines that BMW later said had not received any of the successive improvements made to later production. That's why BMW's 2015 chain campaign covered only cars built up to the end of 2008, as L'argus reported.

2009: new crankshaft

L'argus reported that a new crankshaft part number existed from January 2009. UnixNerd's engine reference notes that the lower chain's sprocket is machined into the crankshaft, so a crankshaft change is also a change to the chain drive. BMW's 2015 campaign did not include fitting this later crankshaft to earlier engines.

N47T / N47TU, from 2010

BMW's US technical training calls the N47TU a second-generation BMW diesel, and describes it alongside the six-cylinder N57TU. The points it documents for the N47TU include:

  • Injectors: Bosch CRI2.5 solenoid injectors at up to 1,800 bar. BMW says they match a 1,800-bar piezo injector on power and economy, with lower HC and CO emissions and lower cost.
  • Pump: a single-piston Bosch CP4.1 high-pressure pump, driven from the timing chain.
  • Turbo: variable nozzle turbine (VNT).
  • Chain drive: still at the flywheel end. BMW describes the matching N57TU drive as two sections, a lower chain to the high-pressure pump and an upper chain to the camshafts, with sleeve-type chains, plastic rails and hydraulic tensioners, plus a separate chain for the oil and vacuum pump. The upper chain, lower chain and oil pump chain also appear in the parts list for BMW's N47 campaign.
  • Emissions: after-treatment designed for US ULEV II rules on the US-market engines.

Did the N47T fix the chain problem? We found no BMW document that says so. BMW France told L'argus that later engines got successive improvements, and BMW limited its campaign to 2007 and 2008 builds, which suggests it considered later engines less exposed. Auto Motor und Sport still treats chain wear as an issue across N47 production from 2007 to 2015, so judge every car on its own evidence.

Known problems

The N47's signature problem is wear of the rear-mounted timing chain and tensioner. EGR cooler leaks, DPF clogging and, on US cars, high-pressure fuel pump failure have all led to bulletins or recalls.

Timing chain wear and failure

  • Symptoms: a metallic rattle from the back of the engine, often first heard only on a cold start, according to Auto Motor und Sport. L'argus says the noise from a stretched chain can be heard from about 1,500 rpm. The engine computer may also log camshaft timing deviations. A chain that breaks can destroy the engine.
  • Cause: L'argus reported that the tensioner could not compensate for chain stretch, and that the bush-type chain needs perfect lubrication, so skipped or overextended oil changes and poor oil make wear worse. Auto Motor und Sport describes the chain as designed particularly thin to cut friction.
  • Fix: replace the chains, guides and tensioners. Because the chains sit at the gearbox end, BMW's own repair procedure for replacing both timing chains starts with removing the engine. That is why the job is expensive.
  • How to confirm: listen to a fully cold start after the car has stood overnight. A technician can check chain stretch, and stored camshaft/crankshaft correlation faults support the diagnosis. A rattle that clears after a few seconds still needs investigating.

Affected production and BMW's 2015 campaign

BMW ran a workshop technical campaign, not a safety recall, for the earliest engines. L'argus reported these details in June 2015:

  • Campaign number: 0011540300, sent to the dealer network on January 23, 2015.
  • Production covered: February 1, 2007 to December 24, 2008.
  • Engines and models: 18d, 20d and 23d in the 1 Series (E81/E87, E82, E88), 3 Series (E90/E91, E92, E93), 5 Series (E60/E61) and X3 (E83).
  • Work under 75,000 km: fit a newly developed chain tensioner.
  • Work over 75,000 km: fit the tensioner and measure chain stretch. Depending on the result, replace the upper chain or both upper and lower chains, with sprockets, rails, the oil pump chain and tensioners.
  • Cost to the owner: BMW France said it covered 100% of parts and labor for cars in range, regardless of where they had been serviced. The work was done when the car visited a dealer, without a letter to the owner.

For cars outside that window, BMW France told L'argus it was covering repairs at close to 100% when the car had been maintained to BMW's schedule, in or out of the dealer network. That was a 2015 French position, and we can't confirm it still applies anywhere today.

Goodwill, UK reports and court rulings

Outside that campaign, help has depended on the country, the car's age and its history.

  • UK: Carbuyer reported in November 2016 on a 2007 1 Series whose timing chain broke about 4,000 miles after a dealer had done recall work on the tensioners. BMW declined goodwill, citing the car's age and that it had been bought outside the BMW network.
  • Germany: in April 2017 the Higher Regional Court in Frankfurt (OLG Frankfurt am Main) rejected two buyers' claims over N47 chain noise in a demonstrator and a new car (cases 24 U 26/15 and 24 U 85/15). It ruled the noise a purely acoustic or comfort issue, not a significant defect.
  • US: the early N47 was never sold in the US, and we found no US timing chain recall for the N47T in the 328d or X3 xDrive28d.

We found no class-action settlement or official UK government action over the N47 chain. If you own an affected car, ask a BMW dealer to check the VIN for campaign 0011540300, and keep every service invoice: the BMW statements above all hinged on maintenance history.

EGR cooler leaks (recall)

  • Symptoms: coolant loss with no visible external leak, and in the worst case smoke or burning smells from the engine bay.
  • Cause: the EGR cooler can leak glycol internally. Combined with soot and high EGR temperatures, the deposits can smolder and melt the intake manifold.
  • Recall, UK: BMW recalled about 268,000 diesel cars in the UK in 2018 and added about 27,000 more in October 2019, according to Which?. The list includes 1 Series 114d to 125d built November 2011 to September 2017 and 3 Series diesels built December 2011 to November 2017, among others. Not every car on it has an N47.
  • Recall, US: NHTSA campaign 18V755000 covered 2013 to 2018 328d and 2015 to 2017 X3 xDrive28d, among other diesels. It was superseded by 21V907000, which needs a new remedy even on cars already fixed under 18V755000, and expanded by 25V700000 for some 2018 328d models in 2025.
  • How to confirm: run the VIN on BMW's recall checker, GOV.UK's vehicle recall service, or NHTSA's lookup.

High-pressure fuel pump (US recall)

NHTSA campaign 21V586000 covers certain 2014 to 2018 328d and 2015 to 2017 X3 xDrive28d models, among others. The high-pressure fuel pump may fail and stall the engine, and dealers replace it free of charge. On the N47TU, that pump is the Bosch CP4.1.

DPF clogging

Short trips stop the DPF from regenerating. BMW's bulletin SI B18 03 10 for the N47T and N57T lists fault codes 245700 (filter highly loaded) and 245800 (heavily contaminated), and says the engine computer runs a regeneration at the latest every 600 miles, or every 250 to 500 miles on short-trip cars. Our DPF regeneration guide explains the warning signs, forced regenerations and when cleaning or replacement is the answer.

Buying checklist for a used N47

Start with the build date and the paperwork, then listen to the engine cold.

  • Build date: a car built between February 2007 and December 2008 should have a record of campaign 0011540300 or of chain replacement. Ask a dealer to check the VIN.
  • Chain history: on any N47, ask whether the chains, guides or tensioner have been replaced, and get the invoice.
  • Cold start: insist on starting the engine cold. Listen at the back of the engine, near the bulkhead, for rattle or whine. Then listen again around 1,500 rpm.
  • Fault memory: scan for timing correlation, DPF and EGR faults. Our OBD-II pre-purchase guide explains how.
  • Oil history: regular oil changes with the correct low-ash oil. Long gaps between services are the biggest warning sign on this engine.
  • Recalls: confirm the EGR cooler recall (and, in the US, the high-pressure fuel pump recall) has been done.
  • Coolant level: unexplained coolant loss can point to an EGR cooler leak.
  • Usage: a car that has only done short trips may have a loaded DPF. Ask how it was used and check for DPF fault codes.

Maintenance that matters

On the N47, oil is chain insurance. Use the right specification and don't stretch the interval.

  • Oil spec: Motul's technical data says BMW Longlife-04 oil must be used in diesel engines with a DPF in any country. Later cars may list newer approvals too, so check your owner's manual, and see our BMW Longlife oil explainer for what each approval means.
  • Oil-change interval: L'argus pointed to neglected maintenance and variable oil quality as risk factors for the chain. We'd change the oil more often than the maximum computer interval, especially on cars that do short trips.
  • DPF-friendly driving: BMW's bulletin says regeneration works best above about 38 mph (60 km/h) at a constant speed for 20 to 30 minutes.
  • Listen for change: a new noise from the back of the engine is worth a diagnosis before it becomes a failure.

Our timing chain vs belt guide explains why a gearbox-end chain is so costly to replace, and the B47 diesel guide covers the engine that replaced the N47. For more BMW diesel walk-throughs, see the channel's video guides.

The N47 at high mileage

A high-mileage N47 can be a good buy, but only with evidence. The engine's reputation rests on one component, so a car with a documented chain replacement and steady oil changes is a lower risk than a low-mileage car with gaps in its history.

Past 150,000 miles, budget for DPF and EGR work as well as the chain, and check the turbo for oil leaks and shaft play. We have not found reliable failure-rate data for the N47, and you should be wary of any percentage quoted online. The questions that matter are simple: when was it built, has the chain or tensioner been done, does it start cold without a rattle, and have the recalls been completed?

If you're choosing between an N47 and a B47 car of similar age and price, the B47 is the newer design. Read our B47 guide before deciding.

Frequently asked questions

Which BMW N47 engines are affected by timing chain failure?

The earliest engines have the strongest evidence. BMW's 2015 campaign covered N47s built from February 1, 2007 to December 24, 2008 in the 118d, 120d, 123d, 318d, 320d, 520d and X3. Later engines received successive updates, but specialists still report chain wear, so check any N47 carefully.

Is the N47T (N47TU) better than the original N47?

It is a revised second-generation engine with new injectors, a CP4.1 fuel pump and a VNT turbo, and BMW's 2015 campaign did not include it. We found no BMW statement that it fully cured chain wear, so cold-start checks and service history still matter.

Did BMW recall the N47 for timing chain failure?

Not as a safety recall. BMW ran workshop technical campaign 0011540300 from January 2015 for 2007 and 2008 builds, fitting a new tensioner and replacing chains where stretch was found. Goodwill outside the campaign has varied by country and case.

How much does an N47 timing chain replacement cost?

We haven't found a reputable published price. The job is expensive because BMW's procedure for replacing both chains starts with removing the engine, so get written quotes from a BMW specialist.

What oil should I use in an N47?

A low-ash oil with the BMW approval in your owner's manual, usually BMW Longlife-04 for DPF-equipped diesels. Change it on time or earlier.

Sources

Lights on.
Subscribe.

Engine walkthroughs for BMW, VW, Audi and Mercedes-Benz owners, on YouTube at @HarisCars.

Subscribe on YouTube