Skip to content

Engine Guides · BMW

BMW N20 and N26 Engine Guide: Specs, Chain Issue, Buying

BMW N20/N26 specs by version, the timing and oil pump chain problem with BMW's 7/70 extension and Gelis settlement, recalls, and a used-car checklist.

13 minVideo walkthroughBy Haris Cars

Video walkthrough of this post.Open on YouTube

The BMW N20 is a 2.0-liter turbocharged four-cylinder with direct injection, Valvetronic and a twin-scroll turbo. BMW introduced it in 2011 to replace the naturally aspirated N52 six, and the N26 is the low-emission (PZEV/SULEV) version sold in some US cars. It is strong, efficient and easy to live with, but cars built through mid-2015 carry a documented timing chain and oil pump drive chain problem, so any N20 you buy needs its chain history checked before anything else.

The video above is Haris's comparison of the N20 with its successor, the B48, and which one holds up better. This guide is the written reference for the N20 and N26, with sources for every number.

N20 at a glance

The N20 is an inline four of 1,997 cc with an 84.0 mm bore and 90.1 mm stroke, built on an aluminum crankcase.

  • Layout: inline four, four valves per cylinder, two overhead camshafts, longitudinal mounting.
  • Displacement: 1,997 cc.
  • Bore × stroke: 84.0 × 90.1 mm (BMW 320i specification sheet).
  • Valvetrain: third-generation Valvetronic variable valve lift and double VANOS. The N20 uses a central VANOS valve with an integrated solenoid instead of the N55's separate solenoid valves.
  • Induction: single twin-scroll turbocharger.
  • Injection: direct injection with Bosch HDEV5.2 solenoid injectors, rated for up to 200 bar system pressure.
  • Block: die-cast aluminum (AlSi9Cu3) crankcase with arc-wire-sprayed iron-coated cylinder bores, a forged crankshaft and two chain-driven balance shafts.
  • Timing drive: chain, split into an upper camshaft drive and a lower drive for the balance shafts and oil pump.
  • Cooling: electric coolant pump and map-controlled thermostat.
  • Compression ratio: 10.0:1 for the 28i-level engine in BMW's US training manual; 11.0:1 for the 184 hp 320i in BMW's European specification sheet.
  • Engine oil capacity: 5.75 liters for the 320i sedan (BMW specification sheet). Check your own car's figure, because capacities vary by model.
  • Years: BMW began phasing the N20 in from September 2011 in the US, and settlement documents list an X1 xDrive28i built as early as March 2011.

Power and torque by version

The N20 was sold in two main outputs, and the figures differ by market rating.

  • 28i-level (for example 328i, European rating): 180 kW / 245 hp and 350 Nm (258 lb-ft) from 1,250 rpm, per BMW's November 2011 3 Series press release.
  • 28i-level, US rating: 240 hp, as BMW quoted for the US Z4 sDrive28i in April 2011.
  • 20i-level (for example 320i, European rating): 135 kW / 184 hp at 5,000 rpm and 270 Nm (with overboost) from 1,250 to 4,500 rpm, per BMW's 320i specification sheet valid from March 2012.
  • N26: BMW's bulletins list it in the PZEV/SULEV versions of the 228i, 328i and 428i. We did not find a BMW document giving separate output figures for it.

BMW's engine code tells you which one you have: in N20B20O0, the "O" marks the upper output class, while "U" marks the lower class.

Where you'll find the N20 and N26

In the US, the N20 powered almost every "28i" BMW of the early 2010s, plus the 320i.

BMW's 2021 settlement bulletin lists these US models and production windows with N20 or N26 engines:

  • E84 X1: sDrive28i and xDrive28i, model years 2012 to 2015.
  • E89 Z4: sDrive28i, 2012 to 2015.
  • F10 5 Series: 528i and 528i xDrive, 2012 to 2015.
  • F22/F23 2 Series: 228i coupe and convertible, 2014 to 2015, including N26 PZEV/SULEV coupes.
  • F25 X3: sDrive28i and xDrive28i, 2013 to 2015.
  • F26 X4: xDrive28i, 2015.
  • F30/F31/F34 3 Series: 320i, 328i, 328i xDrive sedan, Sports Wagon and Gran Turismo, 2012 to 2015, with N26 versions of the 328i sedan and 328i xDrive Gran Turismo.
  • F32/F33/F36 4 Series: 428i coupe, convertible and Gran Coupe, 2014 to 2015, with N26 versions of each.

The engine did not stop in 2015. NHTSA recall 24V-608, covering the same family's electric water pump, lists the 328i, 528i, 228i, 428i and Z4 sDrive28i through the 2016 model year, the X3 28i through 2017 and the X4 xDrive28i through 2018. Outside the US it also came in lower-output form, such as the 184 hp European 320i.

The B48 replaced it as models were updated. When the facelifted 3 Series was revealed in 2015, the 328i was dropped and a 330i with BMW's new B-family 2.0-liter four took its place. If you're choosing between the two, our B48 engine guide covers the newer engine.

Timing chain and oil pump drive chain: the problem that matters

The N20's known weak point is its chain drive. BMW of North America extended warranty coverage on it in 2017 and later settled a US class action over it.

How the chain drive is laid out

The N20 has two chain drives. The upper chain drives the camshafts and runs on a tensioner, a tensioning rail, a guide rail and a slide rail. A separate lower tooth-type chain drives the balance shafts and, through them, the oil pump. The lower chain sits in the oil sump. Because it drives the oil pump, its condition matters as much as the timing chain's.

Symptoms

  • A high-pitched whine from the lower engine that rises with rpm. This is the symptom BMW describes in service bulletin SI B11 03 17, and BMW published a reference sound file for technicians ("N20/N26 High Pitched Engine Noise from Lower Engine Area").
  • Rattle from the front of the engine at start-up. FCP Euro's repair guide lists this as the usual sign of a worn chain and guides. It is a reported pattern, not a BMW bulletin symptom.
  • Sudden failure. The class action plaintiffs alleged that the timing chain and oil pump drive chain modules could fail and cause sudden engine failure and loss of power. BMW denied the allegations and settled without admitting fault.

Cause

BMW's bulletin gives the cause as wear on the oil pump chain drive sprockets. Owners and independent shops commonly report wear or cracking of the plastic timing chain guides. FCP Euro's repair guide puts that down to poor oil maintenance, heat, or the design itself. BMW's own documents do not single out the guide.

How to confirm it

A BMW dealer can test both chains, and BMW's 2021 bulletin describes the procedure.

  • Upper timing chain: the ISTA "Timing chain test," reached through the exhaust VANOS test plan, reports whether the chain is stretched or needs a mechanical check.
  • Oil pump drive chain: the "Evaluating the drive chain for the oil pump" test plan uses a frequency sensor bolted into an empty M8 hole in the cylinder head next to the oil filter housing, plus a current clamp on the No. 1 ignition coil, all read through BMW's IMIB measuring tool.

An independent shop with a stethoscope can hear the whine. The oil pump chain test, though, needs dealer equipment. A generic OBD scanner won't detect chain wear directly, but it may show stored camshaft or VANOS faults. Our OBD-II pre-purchase check explains what to look for.

The fix and the parts

BMW's fix replaces both chain modules together: the oil pump drive chain module, timing chain, tensioner, slide rail, tensioning rail and guide rail, followed by an oil and filter change.

  • 2017 bulletin part numbers: chain drive (oil pump) 11 41 7 605 366, timing chain 11 31 8 648 732, chain tensioner and guide rail 11 31 7 592 877, sprocket 11 31 7 603 944, slide rail 11 31 7 592 850, chain tensioner with gasket ring 11 31 8 685 091.
  • 2021 kit: BMW later bundled the parts into one kit, 11 31 5 A19 AA2 "Set Timing Chain." It also includes the crankshaft sprocket and collar screw, guide-rail bearing bolts, oil pump collar screws, a valve cover gasket set and a VVT motor seal flange.
  • One-time parts: BMW says that if the high-pressure fuel line connections are released, the line must be replaced. The bulletin also lists the oil sump gasket.
  • Repair instruction: 11 31 054, "Replacing timing chain and chain module for oil pump N20, N26." BMW tells technicians not to remove the turbocharger or wastegate actuator for this job.

Parts suppliers sell some of these numbers as "revised" versions. BMW has not published a dated design change for the N20 chain, guides or oil pump drive, so we can't tell you which build date has the improved parts. What the documents do show is where the coverage ends: the 2017 extension covers cars built up to February 2015, and the settlement class runs to builds between February and July 2015, depending on the model.

US warranty extension: SI B11 03 17

In 2017, BMW of North America extended the warranty on the N20/N26 timing chain and oil pump drive chain to 7 years/70,000 miles from the original in-service date.

  • Who it covered: US-specification cars registered, operated and repaired in the US or Puerto Rico. BMW's model list starts with the F30 328i built from 6/2011 and the E89 Z4 from 6/2011, and every listed window ends in 2/2015.
  • What it covered: the oil pump drive chain, the timing chain, and the parts needed to repair them properly.
  • Reimbursement: owners who had already paid for a qualifying repair could apply to BMW for reimbursement.
  • Status: it is not a recall, and coverage ran from the original in-service date. For cars built in 2015 or earlier, the seven years have run out in practically every case.

US class action: Gelis v. BMW of North America

The class action Gelis, et al. v. Bayerische Motoren Werke AG and BMW of North America, LLC (D.N.J., No. 2:17-cv-07386) settled with a reimbursement program and extended coverage. BMW's bulletin SI B11 02 21 says the settlement took effect on June 30, 2021.

  • Class vehicles: US-specification model year 2012 to 2015 N20 and N26 cars built between March 8, 2011 and July 29, 2015, depending on the model.
  • Repair benefit: for cars beyond the 7/70 extension, one diagnosis paid at 100 percent and one repair of the chain modules, or of the engine if a chain failure damaged it. In the first year (to June 29, 2022), any car with 100,000 miles or less qualified regardless of age. From June 30, 2022, the car also had to be under 8 years in service. BMW paid 75 percent of the repair at 70,001 to 80,000 miles, 55 percent at 80,001 to 90,000 miles and 40 percent at 90,001 to 100,000 miles. The work had to be done at an authorized BMW center, and repairs using non-genuine or used parts were excluded.
  • Value: the Third Circuit's 2022 opinion on attorneys' fees notes that the District Court valued the settlement at no less than $27 million.
  • Status in 2026: the 8-year limit runs from the in-service date, so for model year 2012 to 2015 cars it has almost certainly passed. If a car was registered unusually late, a BMW dealer can check eligibility by VIN.

Our timing chain vs belt guide covers chain-wear warning signs across BMW's other engines.

Other documented N20 problems and recalls

Beyond the chains, the N20's documented issues are two US recalls, crankcase ventilation faults and carbon buildup.

Electric water pump recall (24V-608)

  • Symptoms: often none before failure. The recall concerns fire risk, not just overheating.
  • Cause: an improperly sealed electrical connector on the water pump can let water in and short-circuit.
  • Fix: dealers inspect the pump and plug, replace them as needed and fit a protective shield, free of charge. NHTSA lists 720,796 vehicles. Owner letters went out on March 28, 2025.
  • How to confirm: run the VIN on NHTSA's recall lookup and ask the seller for the dealer invoice.

Brake vacuum pump recalls (13V-454 and 14V-627)

  • Symptom: loss of brake power assist.
  • Cause: insufficient lubrication of the engine-driven vacuum pump.
  • Fix: 13V-454 (2013) covered 76,191 cars, including 2012 to 2014 320i/328i and Z4 sDrive28i. The expansion, 14V-627 (2014), adds a locking ring in the camshaft to hold the camshaft seal disk in place, and also covers the 2014 428i.

Crankcase ventilation faults

A faulty crankcase ventilation valve can show up as oil consumption, oil in the intake, rough idle, a whistling noise or high fuel trims. BMW's bulletin SI B11 03 08 gives a crankcase vacuum specification for the N20 and N26 of 35 mbar, measured with dealer equipment. Readings within about 10 percent are acceptable, up to a maximum deviation of 5 mbar. A reading far off that figure points to the valve or internal wear.

Intake valve carbon buildup

The N20 injects fuel directly into the cylinders, so no fuel washes over the intake valves. Deposits can build up there over time and cause misfires and rough running. Our carbon buildup guide explains the symptoms and the walnut-blasting fix.

Buying checklist for a used N20 or N26

Check the chain history first, then the recalls, then the basics.

  1. Ask for chain paperwork. An invoice showing replacement under SI B11 03 17, SI B11 02 21 or with kit 11 31 5 A19 AA2 is the best document an N20 can have.
  2. Find the build month. The warranty and settlement windows end between February and July 2015. The build date is on the door-jamb label and in a VIN decode.
  3. Listen from cold. Ask for the engine to be completely cold, then listen for start-up rattle at the front and a whine from low in the engine that rises with revs.
  4. Get a dealer chain test if you can. The ISTA timing chain test and the oil pump chain evaluation are the only direct measurements.
  5. Check open recalls for 24V-608, 13V-454 and 14V-627 on NHTSA.
  6. Scan for codes, especially camshaft position, VANOS and misfire faults, and check fuel trims.
  7. Look for oil leaks and coolant loss, and check the oil level.
  8. Read the service history for oil change intervals. FCP Euro's repair guide names poor oil maintenance as one cause of fast guide wear.

Maintenance that matters

Use the right oil, change it often, and treat the chain as a wear part.

  • Oil: BMW's 2013 X3 owner's manual, which covers the N20-powered xDrive28i, lists BMW High Performance SAE 5W-30, BMW Longlife-01 and Longlife-01 FE for gasoline engines, in SAE 0W-40, 0W-30, 5W-40 or 5W-30. If approved oil isn't available, you may top up with up to 1 US quart of API SM or better. Our BMW Longlife oil guide explains the approvals.
  • Oil change interval: follow the Condition Based Service display or your manual. Our advice on a chain-sensitive engine is to change oil sooner than the maximum interval. That's a precaution, not a BMW requirement.
  • Fuel: BMW's European 320i specification calls for a minimum of RON 91. Check your manual for your car's grade.
  • Chain: if there's no record of replacement on a 2015-or-earlier car, budget for the full BMW kit rather than a tensioner alone.

The N20 at high mileage

An N20 with a replaced chain drive, a clean recall record and regular oil changes can be a sensible high-mileage buy. One with an original chain and no history is a gamble.

No BMW or court document we reviewed gives a failure rate, so we won't invent one. What the record does show is that the chain issue was serious enough for BMW to extend coverage, settle a nationwide class action and build a dedicated dealer test. It also shows that the engine's other documented issues (the water pump connector and the vacuum pump lubrication) were handled by recall. Beyond that, expect the carbon deposits and crankcase ventilation wear covered above.

Frequently asked questions

Is the BMW N20 a reliable engine?

It can be, once the timing chain and oil pump drive chain have been dealt with. Cars built through mid-2015 fall under BMW's 2017 warranty extension and the Gelis settlement, which shows how seriously the chain issue was taken. Check the repair history before you buy.

What years of the N20 have timing chain problems?

BMW's 2017 warranty extension covers US cars built from 2011 to February 2015. The class settlement covers model year 2012 to 2015 cars built up to July 2015, depending on the model. BMW has not published a date when revised parts entered production.

Is the N20 timing chain warranty still valid?

Almost certainly not for an original 2012 to 2015 car. The 7-year/70,000-mile extension and the settlement's 8-year/100,000-mile limit both run from the in-service date. A BMW dealer can confirm by VIN.

What is the difference between the N20 and the N26?

The N26 is the version fitted to PZEV/SULEV low-emission US models, such as some 328i, 428i and 228i cars. BMW treats both engines the same in its timing chain bulletins and settlement.

Is the B48 better than the N20?

The B48 is the newer design and replaced the N20 as BMW updated its models from 2015. For the full comparison, watch the video above and see our B48 guide linked earlier.

Sources

Lights on.
Subscribe.

Engine walkthroughs for BMW, VW, Audi and Mercedes-Benz owners, on YouTube at @HarisCars.

Subscribe on YouTube