Skip to content

Engine Guides · Mercedes-Benz

Mercedes M264 and M254 Engine Guide (Plus the M274)

Mercedes M274, M264 and M254 2.0 turbo explained: specs by model, how EQ Boost works, documented faults, 15-year warranty extensions and a buying checklist.

14 minVideo walkthroughBy Haris Cars

Video walkthrough of this post.Open on YouTube

The M264 and M254 are the 2.0-liter turbocharged four-cylinders behind most C 300, E 300/E 350, GLC 300 and GLE 350 models built since 2019, and the M274 is the engine they replaced. All three are solid, efficient engines if they have been serviced on time. Each has one documented weak point worth checking before you buy: the M274's crankcase-ventilation valve, the M264's exhaust valve seats (now covered by a 15-year/150,000-mile extended warranty in the US), and, on the newest M254, early camshaft-adjuster bulletins and the 48-volt hybrid hardware.

Haris walks through the engines in the video above. This guide is the written reference, with a source for every specific claim.

M274, M264 and M254 at a glance

All three are aluminum, chain-driven, direct-injection 2.0-liter turbo fours for longitudinal (rear- and all-wheel-drive) Mercedes models. Their transverse front-drive siblings are the M270 and M260.

M274 (US model years 2015 to about 2020)

  • Displacement and bore × stroke: 1,991 cc, 83 × 92 mm in 2.0-liter form. A 1.6-liter M274 was sold outside the US.
  • Construction: die-cast aluminum open-deck crankcase, high-strength aluminum cylinder head, a balance shaft and a hollow-cast crankshaft.
  • Valvetrain: DOHC, four valves per cylinder, chain-driven, with solenoid-controlled intake and exhaust cam phasers. The US 2.0-liter does not have CAMTRONIC variable valve lift. Mercedes used that on the 1.6-liter M270.
  • Fuel and air: direct injection with piezo injectors at up to 200 bar, and a single turbocharger with a vacuum-operated wastegate.
  • Output (C 300, GLC 300): 241 hp at 5,500 rpm and 273 lb-ft from 1,300 to 4,000 rpm.

M264 (US model years 2019 to 2023)

  • Displacement and bore × stroke: 1,991 cc, 83 × 92 mm, the same as the M274. A 1.5-liter version with a smaller bore was sold outside the US.
  • Construction: die-cast aluminum block with cast-iron liners, CONICSHAPE honing (each bore slightly flared at the bottom to cut piston friction), an aluminum-silicon cylinder head and a balance shaft in the 2.0-liter.
  • Valvetrain: DOHC, four valves per cylinder, toothed timing chain, hydraulic cam phasers on both camshafts and CAMTRONIC two-stage valve lift.
  • Fuel and air: piezo direct injection, and a coolant-cooled twin-scroll turbocharger with an electronic wastegate actuator.
  • Output (2019 C 300, 2020 GLC 300): 255 hp and 273 lb-ft.
  • 48-volt option: some versions have a belt-driven starter-generator. The 1.5-liter European C 200 was rated at 184 hp and 280 Nm, plus 10 kW and 160 Nm from the electric machine.

M254 (US model year 2022 onward)

  • Layout: longitudinal 2.0-liter turbo four with direct injection. A 1.5-liter version powers C 180 and C 200 mild hybrids sold in other markets.
  • Construction: NANOSLIDE cylinder coating. A thin iron-carbon layer is arc-sprayed onto the aluminum bores in place of cast-iron liners.
  • Valvetrain: CAMTRONIC, with the timing chain moved to the rear of the engine.
  • Turbo and exhaust: a turbocharger with a switchable flow connection, a two-box catalytic converter mounted directly behind the turbo, and a coated gasoline particulate filter with a third oxygen sensor.
  • Hybrid: a second-generation 48-volt integrated starter-generator (ISG).
  • Output, 2022 C 300: 255 hp and 295 lb-ft, plus up to 20 hp and 148 lb-ft from the ISG for short bursts.
  • Output, 2023 GLC 300: 258 hp and 295 lb-ft, plus up to 23 hp (17 kW) and 148 lb-ft (200 Nm) from the ISG.

Where you'll find each engine

In the US, the quickest way to identify the engine is the model year and badge. If the year sits on a changeover, check the engine code itself. Our engine code guide shows where to look.

  • M274: 2015–2018 C 300 (sedan, coupe and convertible), 2016–2018 C 350e, 2017–2019 E 300, 2016–2019 GLC 300 (Coupe from 2017), 2018–2020 GLC 350e, 2017–2020 SLC 300 and 2016 SLK 300. This list comes from Mercedes-Benz USA's own extended-warranty notice for the engine. The M274 reached the US with the 205-series C-Class in model year 2015.
  • M264: 2019–2023 C 300 (the coupe and convertible kept the M264 after the sedan moved to the M254 for 2022), E 300 and E 350, 2020–2023 GLC 300 and GLC 300 Coupe, and 2020–2023 GLE 350. Mercedes' warranty notice lists the E-Class from model year 2018. Its technician magazine says the M264 began reaching the US in 2019 C- and E-Class models. Mercedes lists the 2017–2019 E 300 under the M274 too, so check the engine code on a 2018 or 2019 car.
  • M254: 2022-on C 300 (206 series) and 2023-on GLC 300 (254 series). Mercedes service documents also list it in the current E-Class (214), CLE (236) and GLE (167). NHTSA recall filings confirm it in the 2024 GLE 350.

How EQ Boost and the 48-volt starter-generator work

EQ Boost is Mercedes' name for a 48-volt mild-hybrid system. One electric machine replaces both the starter and the alternator. It restarts the engine quietly, recovers energy when you slow down, and adds a few seconds of extra torque while the turbo builds boost. It cannot drive the car on its own, which is what makes it a "mild" hybrid. These engines use two generations of it.

M264: belt-driven starter-generator

On M264 versions that have it, the starter-generator mounts on the front of the engine and turns the crankshaft through the accessory belt. Mercedes launched it in 2018 on the 1.5-liter C 200 and quoted 10 kW and 160 Nm of assist. It also handles start/stop, which Mercedes said restarts the engine "almost silently," and it recharges the 48-volt battery during deceleration. Trade press at the time noted that the M264's 48-volt system also runs an electric water pump and allows coasting with the engine off. Not every M264 has this hardware, so check the car's equipment list or ask a dealer to decode the VIN.

M254: integrated starter-generator

The M254 moves the electric machine off the belt and into the driveline, between the engine and the 9-speed automatic. auto motor und sport put the change simply: unlike earlier starter-generators, this one belongs to the transmission rather than the engine. Mercedes' technician magazine calls it a second-generation ISG worth about 15 kW (20 hp) of short-term boost. US ratings vary slightly by model: 20 hp and 148 lb-ft in the C 300, and 23 hp and 148 lb-ft in the GLC 300.

What it means for owners

  • Battery health: the 48-volt lithium-ion battery is a wear item with its own diagnostics. Mercedes bulletin LI54.10-P-080288 (February 2026) covers fault code P0A7F00, a state-of-health warning on the 48-volt battery in the 206, 214, 223 and 254 model series. The fix starts with a capacity check and a restoration routine, and the battery is replaced only if it fails that test.
  • Safety: Mercedes prohibits work on a live 48-volt system and says starter-generator testing must go through its XENTRY diagnosis system. A separate 2026 bulletin (LI54.10-P-080602) warns that some 48-volt batteries can stay energized after the 12-volt battery is disconnected. Leave 48-volt work to a properly equipped shop.
  • Smoother start/stop: the ISG replaces the conventional starter and alternator and brings the engine up to idle speed quickly and smoothly.

Known problems and what to check

Each engine has a documented issue that Mercedes has acknowledged in bulletins or warranty extensions. Most owner complaints you'll read online fall outside those.

M274: crankcase ventilation valve (P052E71)

  • Symptoms: check-engine light with fault code P052E71. Mercedes' symptom list also includes rough running, low power and blue smoke.
  • Cause: the partial-load crankcase ventilation valve, which is part of the intake line assembly, may not work as intended.
  • Fix: on most models, an engine-computer software update plus a cap on the valve connector, with no parts replaced. On the SLK/SLC 300, C 350e and GLC 350e, a guided test decides whether the intake line assembly is replaced. The bulletin is LI01.20-P-076894.
  • Coverage: Mercedes-Benz USA extended warranty on the intake line assembly to 15 years/150,000 miles for the M274 models listed above.
  • Note: Mercedes says that oil at the valve's electrical connector does not by itself justify replacing the wiring harness or engine computer.

M274: cold knocking from early engines (wrist pins)

  • Symptoms: clattering or knocking from the bottom end when cold, up to about 50°C (122°F) oil temperature, heard mostly on deceleration.
  • Cause: Mercedes bulletin LI03.10-P-060916 traced it to an unfavorable wrist-pin tolerance that let the connecting rod float too far in the piston. The bulletin applies to engines built before production clean points of March 27 or April 20, 2015, depending on the plant.
  • Fix: once the noise was confirmed against a reference recording, technicians replaced the pistons, connecting rods and bearings with updated parts.
  • NHTSA's view: a petition linking these pins to 2015 C 300 engine failures was denied in February 2024. NHTSA found no relationship between the wrist-pin condition and engine failure or loss of power.
  • Cracked pistons: owners commonly report these on M274 engines, but we found no Mercedes bulletin or campaign that documents them. Treat any misfire with low compression on an M274 seriously.

M274: low boost and wastegate faults

  • Symptoms: sluggish response with codes such as P029900 or P029909 (boost too low) or P023422 (boost too high).
  • Checks: smoke-test the charge piping, compare the two throttle pressure sensors with the key on and engine off, and confirm vacuum supply. Mercedes' technician magazine says a new vacuum pump makes about 950 mbar and the minimum spec is around 750 mbar.
  • Common cause: field reports cited by Mercedes' technician magazine say a failed wastegate diaphragm is one of the most common faults. On the GLC 300 the actuator isn't sold separately, so the turbo and manifold are replaced as one unit.

M264: exhaust valve seat and guide wear (misfire)

  • Symptoms: check-engine light, rough running, jerky acceleration or shifting, and fault codes for misfire (P030x), mixture formation (P219x) or injector quantity adjustment (P1CEF85, P1CE577).
  • Cause: Mercedes says the exhaust valve guides and/or seats can wear irregularly because of increased lateral forces.
  • Confirm: a cylinder leak-down test. If a valve seat is damaged, the whole cylinder head is replaced, because the seats can't be reworked (bulletin LI01.30-P-072328).
  • Coverage: in January 2026, Mercedes-Benz USA extended coverage of the M264 exhaust valve system to 15 years/150,000 miles. It covers 2019–2023 C 300 models, 2018–2023 E 300/E 350, and 2020–2023 GLC 300 and GLE 350. Owners who already paid for this repair may be eligible for reimbursement.

M264 and M254: recalls

  • 20V-364: on 90 model-year 2020 C 300, E 350 and GLC 300 cars with the M264, the screws holding the turbocharger oil feed and return lines may not have been torqued correctly. An oil leak onto hot parts could start a fire. Dealers inspect the lines and tighten them.
  • 21V-961: on certain gasoline Mercedes models, including the 2016 C 300, 2019 C 300, E 300 and GLC 300, and 2020 E 350 and GLC 300, particles trapped between the fuel rail and injectors could cause a fuel leak. Dealers replace the rail and injectors.
  • 23V-878: on a small number of M254 vehicles, including the 2023 GLC 300 and 2024 GLE 350, the wrong screws on the high-pressure fuel pump could stop it sealing against the tandem oil pump. Dealers replace the fuel pump.

M254: camshaft adjuster central valve

  • Symptoms: vibration at low rpm, with intake (P001100, P001104, P001200) or exhaust (P001400, P001404, P001500) camshaft position codes.
  • Cause: bulletin LI05.20-P-080257 (February 2026, valid for the M254 in all model series) says fluctuating oil pressure can damage the filter screen in the cam adjuster's central valve. If the screen breaks loose, debris can reach the rear camshaft bearing.
  • Fix: replace both central valves and the affected adjuster. If metal particles turn up in the oil filter, the camshaft bearing housing is replaced too.

All three: timing chain noise

Every one of these engines uses a timing chain, not a belt. Mercedes' technician guidance lists several possible causes of start-up rattle: low oil pressure to the tensioner, a failed tensioner, a faulty cam adjuster or a stretched chain. Diagnose the noise before replacing parts. On the M254, the chain sits at the back of the engine, and Mercedes says deep timing repairs mean removing the engine. Our timing chain vs belt guide covers the warning signs.

Buying checklist

Check the paperwork first, then let a scan tool and a cold start tell you the rest.

  • Recalls and extensions: run the VIN at nhtsa.gov/recalls. Ask a Mercedes dealer to check the vehicle record (VMI) for open campaigns and for the M264 cylinder-head or M274 intake-line extensions. Extended coverage is only worth something if the car is still under the age and mileage limits.
  • Stored codes: a full scan, not just a code reader, should show no misfire or mixture codes (M264), no P052E71 (M274), no camshaft position codes (M254) and no 48-volt battery faults. Our OBD-II buying guide explains what to look for.
  • Cold start: ask for the car to sit overnight. Listen for knocking that fades as the engine warms (early M274) and for chain rattle in the first few seconds on any of the three.
  • Leaks: look for oil around the turbocharger oil lines, the timing cover and the engine-to-transmission joint.
  • Service history: look for regular oil changes with the correct MB-approved oil. On an M274, check that spark plugs were genuine Mercedes parts. Mercedes warns that non-indexed aftermarket plugs can cause melted or cracked pistons.
  • Drive it: test smooth pull from low rpm (boost faults), clean start/stop restarts and, on 48-volt cars, the absence of any "48 V" warning in the cluster.

Maintenance that matters

Oil specification and changing it on time matter more than anything else on these engines.

  • Oil approval: use an oil that carries the MB approval listed for your engine in the owner's manual. Mercedes approvals are not interchangeable. Our MB 229 oil guide explains which sheet applies.
  • Interval: Mercedes' technician magazine gives the M274's general schedule as oil and filter every 10,000 miles or one year. Your car's ASSYST service display and maintenance booklet set the actual interval.
  • M254 drain plug: Mercedes requires a new drain plug at every oil change on the M254. It is tightened until it hits its stop, not to a torque figure.
  • Low-speed lugging: small turbo direct-injection engines are prone to low-speed pre-ignition. See our LSPI explainer for why oil quality matters.
  • Intake carbon: all three are direct-injection only, so fuel never washes the intake valves. Our carbon buildup guide covers symptoms and cleaning.

M274 vs M264 vs M254: which to buy

For most buyers, a well-documented M264 with the cylinder-head extension still in force is the sweet spot. The M254 is the most refined of the three but the least proven, and the M274 is the oldest and simplest.

  • M274: no 48-volt mild-hybrid hardware to age, and its main documented fault is the ventilation valve, which is covered by a long extension. The trade-offs are piezo injectors, a vacuum wastegate, and an age at which owner-reported piston failures are hard to rule out on a test drive.
  • M264: more refined, with a twin-scroll turbo and CAMTRONIC. The valve-seat issue is real, but Mercedes now covers it for 15 years or 150,000 miles.
  • M254: the most torque and the smoothest start/stop. It adds a 48-volt battery and ISG to maintain, its timing drive is harder to reach, and bulletins are still appearing. Buy one with factory or certified warranty left.

High-mileage outlook

None of these engines has a documented design flaw that makes 150,000 miles unrealistic, but none has a long enough public track record to promise it either. The M274 is old enough that condition matters more than mileage. Compression, leak-down results and a quiet cold start tell you more than the odometer. On a high-mileage M264, the valve-seat issue becomes an out-of-pocket head job once the car passes 15 years or 150,000 miles. The M254 is too new for any honest high-mileage verdict. Budget for the 48-volt battery as a long-term wear item, and treat any camshaft codes as urgent.

Frequently asked questions

Is the Mercedes M264 engine reliable?

Mostly, yes. Its one significant documented issue is irregular wear of the exhaust valve guides and seats, which causes misfires. Mercedes-Benz USA extended coverage for it to 15 years/150,000 miles on model-year 2018–2023 C-, E-, GLC- and GLE-Class models, with the exact years varying by model. Confirm by VIN that a car qualifies.

What is the difference between the M264 and M254?

The M254 replaces the M264's cast-iron liners with a NANOSLIDE-coated bore and moves the timing chain to the rear of the engine. It adds a close-coupled catalytic converter with a particulate filter. It also swaps the belt-driven starter-generator, which only some M264s have, for a 48-volt integrated starter-generator between the engine and transmission.

Do the M274, M264 and M254 have a timing belt or chain?

All three use a timing chain. There is no scheduled replacement interval, but a rattle at start-up or camshaft correlation codes should be diagnosed promptly.

What does EQ Boost add on a Mercedes four-cylinder?

On the M254, the 48-volt starter-generator adds up to 20 hp and 148 lb-ft in the 2022 C 300, or 23 hp and 148 lb-ft in the 2023 GLC 300, for short bursts. On the 1.5-liter M264 C 200, the belt-driven unit added 10 kW and 160 Nm.

Which Mercedes models have the M274?

In the US: the 2015–2018 C 300 and C 350e, 2017–2019 E 300, 2016–2019 GLC 300, 2018–2020 GLC 350e, 2017–2020 SLC 300 and 2016 SLK 300.

Sources

Lights on.
Subscribe.

Engine walkthroughs for BMW, VW, Audi and Mercedes-Benz owners, on YouTube at @HarisCars.

Subscribe on YouTube