Engine Guides · BMW
BMW S58 Engine Guide: Specs, Problems and Buying Advice
BMW S58 explained: specs and power for each M3, M4, M2 and X3 M, the bearing-shell campaigns, M Ignite, and what to check before buying a used one.
12 minVideo walkthroughBy Haris Cars
The S58 is BMW M's 3.0-liter twin-turbo inline-six. It replaced the S55 in 2019 and powers the X3 M, X4 M, G80 M3, G82 M4 and G87 M2. BMW built it on the B58TU production engine, then gave it forged internals, two turbos and an M-specific oil and cooling system. It suits owners who want a fast, usable M car with a sound track record so far. The main watch-out is a set of BMW main-bearing-shell campaigns on specific production windows, so check any car's VIN for open campaigns before buying.
Haris walks through the engine in the video above. This guide is the written reference, with a source for every specific claim.
S58 at a glance
The S58 is a 2,993 cc closed-deck aluminum inline-six with a forged crank, two mono-scroll turbos and 350-bar direct injection. The figures below come from BMW's press material and its S58 technical training manual.
- Displacement: 2,993 cc
- Bore × stroke: 84.0 × 90.0 mm. The B58 it is based on is 82.0 × 94.6 mm.
- Compression ratio: 9.3:1
- Block: closed-deck aluminum crankcase with wire-arc-sprayed iron coating on the cylinder walls instead of liners
- Crankshaft and rotating assembly: forged steel crankshaft weighing about 21.2 kg (47 lb), forged connecting rods and forged Mahle pistons
- Cylinder head: aluminum head with a 3D-printed core, which lets BMW route the coolant passages more freely and saves weight. Valvetronic and VANOS cam timing.
- Induction: two mono-scroll turbochargers, one for cylinders 1 to 3 and one for 4 to 6, with electric wastegates and indirect (water-to-air) charge cooling
- Injection: direct injection at up to 350 bar (above 5,000 psi), fed by two high-pressure pumps
- Timing drive: a single chain, using the same concept as the B58TU
- Redline: 7,200 rpm in the M2, M3 and M4
- Oil system: a two-chamber sump with an extra suction stage and a map-controlled oil pump. Oil capacity is 7 liters in the X3 M and X4 M.
- Years: 2019 on. Production of the X3 M and X4 M began in April 2019.
Output varies a lot by model, market and year. These are US ratings from BMW unless noted:
- 2020 X3 M / X4 M: 473 hp; 442 lb-ft
- 2020 X3 M / X4 M Competition: 503 hp; 442 lb-ft
- 2022 X3 M / X4 M facelift: 473 hp and 457 lb-ft; Competition 503 hp and 479 lb-ft
- 2021 M3 / M4 (six-speed manual): 473 hp at 6,250 rpm; 406 lb-ft
- 2021 M3 / M4 Competition (eight-speed automatic): 503 hp at 6,250 rpm; 479 lb-ft
- M4 CSL (production from July 2022): 405 kW, given by BMW as 550 hp in metric horsepower; 650 Nm (479 lb-ft)
- M3 CS (production from March 2023): 543 hp; 479 lb-ft
- 2023 M2: 453 hp; 406 lb-ft
- 2025 M2: 473 hp; 406 lb-ft with the manual, 443 lb-ft with the automatic
- 2025 M4 Competition xDrive: 523 hp; 479 lb-ft
- European ratings: BMW's training manual gives 353 kW (480 PS) for the standard engine and 375 kW for the Competition.
Where you'll find the S58
The S58 is used only in M cars. It doesn't appear in M Performance models such as the M340i, which use the B58. If you aren't sure which engine a car has, our guide to finding your exact engine code shows where to look.
- X3 M and X4 M (F97/F98): 2020 model year on, built in Spartanburg, South Carolina. Facelifted for the 2022 model year, with US market launch in September 2021.
- M3 Sedan (G80) and M4 Coupe (G82): US launch in March 2021. M xDrive arrived for Competition models in summer 2021. The M4 Convertible (G83) uses the same engine.
- M4 CSL: a limited run of 1,000 cars, built at Dingolfing from July 2022
- M3 CS: built in limited numbers at Munich from March 2023, with M xDrive all-wheel drive
- M2 (G87): launched in April 2023, rear-wheel drive only, built in San Luis Potosí, Mexico
Versions and revisions
The S58 hasn't had a formal "TU" like the B58. BMW has instead raised output model by model, mostly through boost and engine management, and introduced a larger update, M Ignite, in 2026.
How the S58 differs from the B58TU
BMW's training manual says the S58 is based on the B58TU but changes most of what matters for a high-revving engine:
- Bore and stroke: 84 × 90 mm, a bigger bore and shorter stroke than the B58's 82 × 94.6 mm, which suits higher revs
- Head gasket: four layers instead of the B58TU's three, because of higher combustion pressure
- Cooling: the B58's split-cooling system is dropped and the water chambers in the head are enlarged
- Oil pump: the B58TU's variable vane pump would have been too large once the extra suction pump was added, and couldn't supply oil reliably at the S58's engine speeds. BMW fitted a map-controlled gear pump with an integrated return pump instead.
- Turbos: two mono-scroll units replace the B58's single twin-scroll
Power increases on special models
The M4 CSL got its extra power mainly by raising the maximum boost of the two turbos from 1.7 to 2.1 bar, plus model-specific engine management and stiffer engine mounts. BMW quotes the same boost change for the M3 CS, given in US units as 24.7 to 30.5 psi. For 2022, BMW said the X3 M and X4 M adopted the lightweight forged crankshaft from the M3 and M4.
BMW M Ignite (from mid-2026)
BMW announced M Ignite in May 2026. It is a pre-chamber ignition system with its own spark plug and coil in each cylinder, working alongside the conventional plug. The pre-chamber takes the lead at higher revs and loads. The engine also gets a higher compression ratio and turbochargers with variable turbine geometry.
- Timing: M3 and M4 production with M Ignite starts in July 2026, and the M2 follows in August 2026
- Output: BMW says displacement and power outputs are unchanged from the outgoing engines
- Why: BMW claims a significant cut in fuel consumption under high load and links the system to Euro 7, which BMW says comes into force in November 2026
This is new hardware, so there's no long-term ownership record yet.
Known S58 problems
The S58's documented issues so far are mostly manufacturing campaigns on specific build windows, not design flaws that affect every engine. The main one involves main bearing shells. Below, BMW-documented items come first and owner-reported ones are labeled.
Main bearing shells (BMW campaigns)
BMW has twice stopped deliveries of S58 cars over bearing shells, and in 2026 it notified owners about a main-bearing service action.
- October 2021 (SIB 11 07 21): a delivery stop on some 2022 model-year X3 M, X4 M, M3, M4 and M4 Convertible built between July 13 and September 23, 2021. BMW lists the affected engine types as S58O and S58T.
- February 2026 (SIB 11 01 26): a delivery stop on some 2026 model-year M3, M4, M4 Convertible and M2 built between October 16, 2025 and January 28, 2026
- March 2026 owner notification: a BMW in-car and in-app message filed with NHTSA says a manufacturing defect may cause the sliding layer of the main bearing shells to peel, which in some cases may damage the engine. The shells are replaced free. The notice itself doesn't list models. A bulletin index compiled from NHTSA filings lists it against the 2025 M3.
Symptoms: BMW's documents don't describe symptoms. How to confirm: ask a BMW dealer to check the VIN for open or completed campaigns, and get a printout. Fix: replacement of the bearing shells under the campaign.
Emissions recall 25E-A03 (engine software)
This campaign covers X3 M and X4 M, M3, M4, M4 Convertible and M2 built from November 2021 to January 2025. Because of a DME software error, the check-engine light did not come on when fault code P15A3 was stored. The fix is a DME software update. On a used car it's worth confirming, because a light that should have been on may have hidden a fault.
Oil consumption and oily turbos
BMW's training manual warns technicians not to condemn a turbo just because it's fouled with oil. If oil is present where the blow-by gases enter, the whole engine must be checked for leaks first. BMW says faulty gaskets or crankshaft seals can raise blow-by, and leaking crankshaft seals can cause oil consumption of up to 3 liters per 1,000 km (620 miles). If a seller or shop says the car "needs turbos" for oil use, ask how the rest of the engine was checked.
Other bulletins
- Charge air cooler housing (SIB 17 03 22): on the M3, M4 and M4 Convertible, an improperly crimped housing may separate and lose boost. BMW says this service action involved only three vehicles, so it's not a pattern.
Owner- and retailer-reported issues
These come from parts retailers and owner reports, not BMW documents. Treat them as things to check, not proven defects:
- Wastegate rattle: a metallic rattle on deceleration or light load, especially when cold, blamed on play in the wastegate actuator arms
- Carbon buildup: the S58 is direct injection, so fuel doesn't wash the intake valves. One retailer reports rough idle and cold-start hesitation on affected engines. Our carbon buildup guide explains how it's confirmed and cleaned.
- High-pressure fuel pump noise and wear: reported mainly on tuned cars with raised fuel demand
- Oil cooler leaks: leaks at the front of the engine on early units
The S55's crank-hub problem is a common worry for buyers. One parts retailer lists a related crank reluctor issue for some early S58s, but it cites no source, and we found no BMW recall or service bulletin for an S58 crank hub. Until there is evidence, treat it as unproven.
Buying checklist for a used S58
An S58 car's history matters as much as its mileage. Check these before you hand over money:
- Campaigns: get a BMW dealer printout showing the bearing-shell campaigns (where applicable) and emissions recall 25E-A03 as completed, not open. Also run the VIN on nhtsa.gov.
- Tuning history: ask directly about ECU tunes, downpipes and fuel or turbo upgrades, and check for software that's been flashed back to stock. Higher boost changes the load on the bottom end and fuel system.
- Track use: look for track tires, brake pad dust, tow-hook marks and event stickers. Track use isn't a problem if the oil and brakes were serviced to match.
- Fault codes: scan for stored and history codes, including P15A3 on cars built before the 25E-A03 software fix. Our OBD-II pre-purchase guide explains what a generic scanner shows and misses.
- Cold start: listen for rattles from the turbos on startup and on lift-off. Check the exhaust for smoke.
- Leaks: look under the car at the front of the engine, the oil cooler area and around the turbos.
- Oil consumption: ask how often the owner tops up. High consumption needs a diagnosis, not a guess.
- Service records: look for regular oil services with BMW-approved oil, more often if the car saw track days.
Maintenance that matters
Oil quality and level are the S58's biggest maintenance lever. The engine relies on its map-controlled pump and two-chamber sump to keep oil supply steady under hard cornering and braking.
- Oil spec: a 2020-printed US M3 Sedan owner's manual lists BMW Longlife-01 FE in SAE 0W-30. It allows up to 1 US quart of API SL, SM or SN oil as a top-up only. Check your own manual and the label under the hood. Our BMW Longlife oil guide explains the approvals and the EU-only rules.
- Oil change interval: follow the interval the car displays as the maximum. Shorter intervals are common on tracked or tuned cars, but that's owner practice, not a BMW requirement.
- Oil level: check it regularly, especially before and after track days
- Cooling: the S58 has a main radiator, two auxiliary radiators in the front wheel wells, a separate low-temperature circuit with an electric pump for the charge air cooler, and an extra electric pump that keeps cooling the turbos after shutdown. Keep coolant at the correct level and use BMW-approved coolant.
- Timing chain: it uses the same single-chain concept as the B58TU. Clean oil at the right level is its best protection. Our timing chain guide covers chain vs belt tradeoffs.
The S58 at high mileage
The S58 has only been on sale since 2019, so there's limited public evidence on how it holds up past 100,000 miles, especially in M3 and M4 use. We won't put a failure rate on it, because nobody has published one we'd trust.
What we can say is that the basic architecture is strong. It has a closed-deck block, a forged crank, rods and pistons, a racing-style oil supply and the cooling capacity BMW designed for track use. The problems on record so far are build-quality campaigns tied to production windows, which a VIN check can rule in or out. The X3 M and X4 M went on sale first, in 2019, so they are the oldest and often highest-mileage S58 cars on the used market.
For a high-mileage example, favor stock cars with complete BMW or specialist records and documented campaign work. Be more cautious with heavily tuned cars of unknown history. If you want a cheaper, simpler engine from the same family, read our B58 engine guide.
Frequently asked questions
Is the BMW S58 reliable?
So far, yes, with one caveat. Its documented problems are BMW campaigns on specific production windows, chiefly main bearing shells, rather than a design fault across all engines. Long-term data past 100,000 miles is still limited.
Is the S58 based on the B58?
Yes. BMW's training manual says the S58 is based on the B58TU. It has a longer 90 mm stroke with an 84 mm bore, a forged crank, two mono-scroll turbos instead of one twin-scroll, a 9.3:1 compression ratio and an M-specific oil and cooling system.
Does the S58 have the S55 crank hub problem?
We found no BMW recall or service bulletin for an S58 crank hub. Online claims about it don't cite evidence. The issues BMW has documented on the S58 are bearing-shell and software campaigns.
How much horsepower does the S58 make?
It depends on the model. US ratings run from 453 hp in the 2023 M2 to 543 hp in the M3 CS, and BMW rates the M4 CSL at 405 kW. The common figures are 473 hp for standard models and 503 hp for Competition models, with 523 hp for the 2025 M4 Competition xDrive.
What is BMW M Ignite?
M Ignite is a pre-chamber ignition system BMW added to the S58 from July 2026 for the M3 and M4 and August 2026 for the M2. It works alongside variable-geometry turbos and a higher compression ratio. BMW says power outputs are unchanged and fuel use under high load drops significantly.
Sources
- BMW Group technical training (via Bimmerpost): ST1926 S58 Engine, February 2019
- BMW Group Americas newsroom: The first-ever 2020 BMW X3 M and BMW X4 M
- BMW Group Americas newsroom: The new BMW X3 M Competition and X4 M Competition (2022)
- BMW Group Americas newsroom: The new 2021 BMW M3 Sedan and M4 Coupe
- BMW Group newsroom: The all-new BMW M4 CSL
- BMW Group Americas newsroom: The BMW M3 CS
- BMW Group Americas newsroom: The all-new BMW M2
- BMW Group Americas newsroom: New 2025 BMW M2
- BMW Group Americas newsroom: The new 2025 BMW M4 Coupe and M4 Convertible
- BMW Group newsroom: BMW M Ignite technology (May 2026)
- BMW NA via NHTSA: SIB 11 07 21, delivery stop, main bearing shell
- BMW NA via NHTSA: SIB 11 01 26, delivery stop, bearing shell
- BMW NA via NHTSA: in-vehicle/in-app service action notification, main bearing shell (March 2026)
- BMW G80 service bulletin index (compiled from NHTSA filings)
- BMW NA via NHTSA: SIB 12 01 25, emissions recall 25E-A03, DME programming
- BMW NA via NHTSA: SIB 17 03 22, service action, replace the charge air cooler
- BMW Group technical training (via Internet Archive): ST1505 B58 Engine
- Euro Premium Parts: BMW S58 engine guide (retailer-reported issues)
- BMW M3 Sedan owner's manual, October 2020 print (via ManualsLib): engine oil
Keep reading
Related posts

Engine Guides
BMW B58 Engine Guide: Specs, Problems and Buying Advice
BMW B58 3.0 turbo six explained: specs by version (B58, TU, TU2), the Supra link, known problems backed by BMW bulletins, and used-buyer checks.
BMW14 minVideo

Owner Guides
BMW LL-01 vs LL-04 vs LL-17 FE+: Which Oil Does Your BMW Need?
BMW Longlife oils decoded: what LL-01, LL-04, LL-12 FE, LL-14 FE+, LL-17 FE+ and LL-19 FE mean, which engines take which, and US vs EU rules.
BMW8 min

Engine Guides
BMW N55 Engine Guide: Specs, Problems and Buying Advice
BMW N55 3.0 turbo six explained: verified specs by model, the VANOS recall, common leaks and water pump faults, N54 differences and a used-car checklist.
BMW11 min

Engine Guides
BMW B38 Engine Guide: Specs, Problems and Buying Advice
BMW and MINI B38 1.5 three-cylinder: verified specs by model, the 2015 thrust bearing fix, leaks, recalls, oil spec and a used-car checklist.
BMW12 minVideo

Engine Guides
BMW B47 Diesel Guide: Specs, EGR Recall and Problems
BMW B47 2.0 diesel explained: verified specs by model, the EGR cooler recall and its scope, damper and DPF issues, and a used-buyer checklist.
BMW12 minVideo

Engine Guides
BMW M54 Engine Guide: Specs, Problems and Buying Checks
BMW M54 2.2, 2.5 and 3.0 specs by market, where it was fitted, CCV, cold-climate and cooling problems with BMW bulletins, and a used-car checklist.
BMW10 minVideo

Lights on.
Subscribe.
Engine walkthroughs for BMW, VW, Audi and Mercedes-Benz owners, on YouTube at @HarisCars.
Subscribe on YouTube