Engine Guides · BMW
BMW B38 Engine Guide: Specs, Problems and Buying Advice
BMW and MINI B38 1.5 three-cylinder: verified specs by model, the 2015 thrust bearing fix, leaks, recalls, oil spec and a used-car checklist.
12 minVideo walkthroughBy Haris Cars
The BMW B38 is a turbocharged, direct-injected three-cylinder gasoline engine, made mostly as a 1.5-liter, that BMW Group has used since 2014 in the MINI Cooper, front-drive 1, 2 and X1/X2 models, the 318i, several plug-in hybrids and, in high-output form, the i8. It is a sound choice for a small BMW or MINI if the car was built after spring 2015 and has had regular oil changes. The main watch-outs are a crankshaft thrust bearing problem on early engines, coolant and oil leaks, and the usual direct-injection carbon buildup.
Haris walks through the engine in the video above. This guide is the written reference, with a source for every spec, recall and bulletin we cite.
B38 at a glance
The B38 is the three-cylinder member of BMW's modular engine family, built around roughly 500 cc per cylinder, with the timing chain at the transmission end.
- Layout: inline three-cylinder, four valves per cylinder, turbocharged gasoline.
- Displacement: 1,499 cc for the 1.5-liter. A 1,198 cc 1.2-liter version powered the early MINI One.
- Bore × stroke (1.5): 82 × 94.6 mm, the same cylinder dimensions BMW lists for the B46 four-cylinder.
- Compression ratio: 11.0:1 on the 1.5-liter road-car versions, and 9.5:1 on the i8's B38K15T0.
- Valvetrain: double overhead camshafts with VANOS variable cam timing and Valvetronic variable valve lift (BMW's "TwinPower Turbo" package).
- Injection: gasoline direct injection, with BMW quoting rail pressure of up to 200 bar.
- Induction: single turbocharger with an electrically adjustable wastegate.
- Block and head: aluminum. BMW's Bx8 training manual describes a heat-treated all-aluminum crankcase with electric arc wire-sprayed cylinder walls, covering the B38 and B46 in one document.
- Timing drive: chain, on the transmission side of the engine.
- Balance: a balancer shaft to smooth the three-cylinder's natural shake, per Auto Świat and UnixNerd.
- Years: 2014 onward.
Power and torque depend on the car, so here are the published figures by application:
- MINI One 1.2 (F56, 2014): 75 kW (102 hp) at 4,250 to 6,000 rpm and 180 Nm from 1,400 rpm, per MINI's launch press kit.
- MINI Cooper 1.5 (F56, 2014): 100 kW (136 hp) and 220 Nm from 1,250 rpm, or 230 Nm on overboost, per the same press kit.
- BMW 218i Active Tourer (2014): 134 bhp and 162 lb-ft, per What Car?'s launch report.
- BMW 118i (F40, 2019): 103 kW (140 hp) and 220 Nm, with a brief 10 Nm overboost in fourth gear and above, per BMWBlog's launch coverage.
- BMW X1 sDrive18i (U11, 2022): 100 kW (136 hp), per BMW's launch release.
- MINI Cooper S E Countryman ALL4 plug-in hybrid (2017): 134 hp and 162 lb-ft from the engine, plus an 87 hp rear motor, for 221 hp combined (US figures).
- BMW i8 (B38K15T0): 170 kW (231 hp) at 5,800 rpm and 320 Nm at 3,700 rpm, per BMW's i8 powertrain training manual.
Where you'll find the B38
The B38 sits in compact front-drive BMWs and MINIs, a few rear-drive BMWs, several plug-in hybrids and the i8.
The engine arrived with the third-generation MINI hatch in 2014: MINI's press kit, dated January 2014, gave the 1.5 for the Cooper and the 1.2 for the One. On the BMW side, the front-drive 218i Active Tourer, revealed in February 2014, was among the first applications. Rear-drive versions followed in the 218i coupe and the 318i.
Applications listed by BMW sources and trade press include:
- MINI: F55/F56/F57 Cooper and One, F54 Clubman Cooper, F60 Countryman Cooper, and the Cooper S E Countryman ALL4 plug-in hybrid.
- BMW 1 and 2 Series: F20/F21 116i and 118i, F40 118i, F22/F23 218i coupe and convertible, F44 218i Gran Coupe, F45/F46 216i and 218i Active and Gran Tourer, and the 225xe Active Tourer plug-in hybrid.
- BMW 3 Series: F30/F31 318i after the 2015 update.
- BMW X1 and X2: F48 X1 sDrive18i, F39 X2 sDrive18i, and the later U11 X1 sDrive18i.
- BMW i8: coupe and roadster, as the B38K15T0, mounted transversely ahead of the rear axle and driving the rear wheels, with an electric motor driving the front wheels.
Market matters. In Europe the B38 was the volume gasoline engine in many small BMWs, from the 116i to the 218i Gran Coupe. In the US you're most likely to meet it in a non-S MINI Cooper, a Countryman plug-in hybrid or an i8. NHTSA's recall records show i8s from the 2014 through 2020 model years.
Versions and revisions
The B38 has had one important mechanical fix, one emissions update, and a separate high-output version for the i8.
Early engines and the April 2015 bearing change
The first B38 crankshafts used a combined hydrodynamic thrust bearing in a 180-degree half-shell design. BMW told BimmerToday in 2017 that frequent clutch use wore this bearing prematurely, and that production switched to a 360-degree thrust bearing from April 2015. Details are under Known problems below.
2018: gasoline particulate filter
From July 2018 production, BMW fitted a gasoline particulate filter (GPF, also called an OPF) to its European gasoline engines, the B38 among them, to meet Euro 6d-TEMP. Some models, including the facelifted 2 Series Active Tourer and Gran Tourer and the i8, already met that standard. Like a diesel DPF, a GPF can load up with soot on a diet of short trips and needs longer runs to clear.
2019 onward
The 118i in the 2019 F40 1 Series gained 3 kW to 103 kW (140 hp), and BMWBlog reported the revised engine is 5 kg lighter than before. The 2022 X1 sDrive18i kept the three-cylinder at 100 kW (136 hp).
A practical note from Auto Świat: BMW changed the factory coolant for these engines at the end of 2018, from the blue LC-87 to the green LC-18, and the two should not be mixed. Check what's in the expansion tank before topping up.
The i8's B38K15T0
The i8 version is a heavily reworked B38. BMW's training manual for the i8 lists the main changes:
- Bottom end: main and connecting-rod bearing diameters increased to 50 mm.
- Cylinder head: gravity cast, for higher density and strength.
- Valves: exhaust valve stems increased to 6 mm to stop valve vibration under high boost.
- Boost: up to 1.5 bar, with an electric wastegate and the turbine housing integrated into a steel manifold.
- Starting: no conventional starter. A high-voltage starter-generator on an eight-rib belt starts the engine.
- Compression and fuel: 9.5:1, designed for 98 RON fuel.
Known problems
The B38's one well-documented defect is premature crankshaft thrust bearing wear on early engines. Most other faults are leaks and wear items that owners and specialists commonly report.
Crankshaft thrust (guide) bearing wear on 2014 to 2015 engines
- Symptoms: MINI's US bulletin SI M11 13 16 (November 2016) lists a clutch pedal that misbehaves during shifting, an engine warning light with a crankshaft sensor fault stored, and noise from the lower engine and bellhousing area. It says engine damage can occur in rare cases. Auto Świat describes knocking from the bottom of the engine.
- Cause: the original 180-degree half-shell thrust bearing wore early under frequent clutch use, according to BMW's statement to BimmerToday. Two German magazines' 100,000 km tests of a 218i Active Tourer both ended with major engine work.
- Fix: production moved to a 360-degree thrust bearing from April 2015. BMW said earlier cars were covered by a free, worldwide technical campaign. In the US, SI M11 13 16 applied to F55 and F56 MINI Cooper Hardtops built December 2014 to June 2015. The dealer inspects and fits a guide bearing repair kit. If the bearing or crankshaft is already damaged, the engine is replaced.
- How to confirm: a dealer can show whether the campaign is open or completed for the VIN. The bulletin also says engines replaced with a new or remanufactured unit on or after June 1, 2015 already comply.
Coolant loss
- Symptoms: a falling coolant level, a sweet smell after a drive, or a low-coolant warning.
- Cause: Auto Świat names coolant loss at the turbocharger. The turbo is coolant-cooled, so it has coolant lines and joints in a hot area. BMWBlog lists water pumps and thermostats as wear items owners should expect to replace eventually. On the transverse Bx8 engines the mechanical coolant pump and map-controlled thermostat form one unit.
- Fix: find the leak (turbo lines, pump/thermostat housing) and replace the leaking part. Use the coolant type that's already in the car.
- How to confirm: pressure-test the cooling system and look for dried coolant residue around the turbo feed and return lines and the pump housing.
Oil leaks
Auto Świat lists oil leaks, the oil pan among them. Check the pan seam and the area under the engine for fresh oil. A slow seep isn't urgent, but oil dripping onto the exhaust or a falling oil level needs attention. BMW's Bx8 manual notes these engines have no dipstick and monitor oil level electronically, so check the level through the car's menu.
Wastegate rattle
Both Auto Świat and BMWBlog describe a light rattle at low rpm that can come from the turbo's wastegate. BMWBlog calls it more of an annoyance than a reliability problem. The B38 uses an electrically adjustable wastegate, so a dealer or specialist can check the actuator with diagnostics before anyone condemns the turbo.
Intake valve carbon buildup
The B38 is direct-injected, so fuel never washes the intake valves and deposits build up over time, especially on cars that only do short trips. Symptoms are rough idle, misfire codes and lost response at higher mileage. The fix is a walnut-blast or similar intake valve clean. Our guide to carbon buildup on direct-injection engines covers the cleaning methods and which BMW engines are affected.
Coils and spark plugs
BMWBlog notes ignition coils and plugs can fail early, as on other BMW gasoline engines. A misfire code on one cylinder is the usual sign. Swap the coil to another cylinder: if the misfire follows it, the coil is bad.
Timing chain
Chain trouble is not a common B38 complaint, but Auto Świat notes some engines needed timing work before 100,000 km. The chain sits at the transmission end, so access is hard. The oil pump has its own chain, and Auto Świat suggests checking it whenever the timing drive is opened. A rattle on a cold start that fades as oil pressure builds is the sign to investigate.
Recall: crankshaft sensor firmware (US)
NHTSA campaign 18V465000 covered certain 2018 and 2019 BMW and MINI models, including the MINI Cooper, Countryman and Clubman. The crankshaft sensor may have incorrect firmware and can cause a stall. Dealers replace the sensor free of charge. Run the VIN on NHTSA's recall lookup to see whether it's been done.
Buying checklist for a used B38
Check the build date first, then the service history, then the engine itself.
- Build date: anything built before April 2015 needs proof that the thrust bearing campaign was done, or that the engine was replaced. Ask a BMW or MINI dealer to check the VIN for open campaigns and recalls.
- Clutch feel (manuals): a clutch that sticks, judders or behaves oddly on an early car can point to the bearing problem, not just a worn clutch.
- Cold start: start it from cold yourself. Listen for knocking from the bottom of the engine, a chain rattle that fades after a few seconds, or a metallic buzz at low rpm (wastegate).
- Fault memory: scan for stored codes, especially crankshaft sensor, misfire and cooling faults. Our OBD-II pre-purchase guide shows how.
- Coolant: check the level cold and look for dried residue around the turbo lines and pump housing.
- Oil leaks: look under the engine at the oil pan.
- Vibration at idle: a three-cylinder relies on its balancer shaft and mounts to stay smooth. Sit in the car at idle in Drive with the A/C on. Excessive shake through the seat or steering wheel calls for a closer look at the mounts.
- Service records: look for regular oil changes with the correct BMW Longlife oil. A car that only ever followed the maximum computer interval is a weaker buy than one changed more often.
- Plug-in hybrids: on a 225xe, X2 xDrive25e, Countryman plug-in or i8, also check the high-voltage battery recall history by VIN.
Maintenance that matters
Oil quality and oil-change frequency do more for a B38's life than anything else.
- Oil spec: Motul's technical data says BMW Longlife-17 FE+ is especially suitable for BMW's Bx8 gasoline engines (B38, B46/B48, B58) built from 2014, and that it replaces LL-14 FE+ for GPF-equipped BMW and MINI gasoline engines. MINI's own thrust bearing service action specified 4.25 liters of 0W-20. Your owner's manual has the final word for your car. Our BMW Longlife oil explainer covers LL-01 FE, LL-17 FE+ and what's backward compatible.
- Oil-change interval: Auto Świat's author calls the computer's 30,000 km interval too long and recommends 10,000 km, and no more than 15,000 km. That is an editorial recommendation, not a BMW figure. We'd lean toward the shorter interval on a car that does short trips.
- Spark plugs and air filter: Auto Świat suggests every second oil change. Check the service schedule for your car.
- Coolant: top up with the type already in the system, LC-87 (blue) or LC-18 (green). Don't mix them.
- Driving pattern: short trips are hard on GPF-equipped cars and on intake valve deposits. A regular 20-minute run at steady speed helps both.
The B38 shares its chain-at-the-back layout with the B48 and B58. Our timing chain vs belt guide explains why that position makes chain work expensive, and the B48 engine guide covers the four-cylinder sibling. The channel's video guides cover more of BMW's modular engines.
The B38 at high mileage
A post-April 2015 B38 with regular oil changes has no widely reported structural weakness. BMWBlog wrote that it found no widespread reports of bottom-end failures. Early engines are a different case: those built before the bearing change need proof the campaign was done.
Past 100,000 miles, budget for the wear items above: a coolant leak repair, coils and plugs, an intake valve clean and possibly mounts. Chain work is less likely but expensive when needed, because of where the chain sits. We have not found reliable failure-rate data for the B38, so treat any percentage you see online with suspicion. Judge the individual car: its build date, its oil-change history and how it sounds from cold.
Tuned engines deserve extra care. BMWBlog warns that aggressive tuning without supporting upgrades can quickly hurt reliability, because the stock turbo, fuel system and cooling set the limits.
Frequently asked questions
Is the BMW B38 engine reliable?
Mostly, yes. Engines built from April 2015 onward avoid the early thrust bearing problem, and the common faults after that are leaks, coils and carbon buildup rather than major internal failures. Service history matters more than mileage.
Which cars use the B38 engine?
The MINI Cooper and One (F55/F56/F57), Clubman and Countryman, the BMW 116i/118i, 216i/218i, 318i, X1 and X2 sDrive18i, the 225xe and other plug-in hybrids, and the i8.
What was the B38 thrust bearing problem?
Early B38 crankshafts used a 180-degree half-shell thrust bearing that wore prematurely with frequent clutch use. BMW switched to a 360-degree bearing in April 2015 and ran a free technical campaign for earlier engines. In the US, MINI's bulletin SI M11 13 16 covered F55 and F56 Coopers built December 2014 to June 2015.
What oil does the B38 take?
Oil-maker data lists BMW Longlife-17 FE+, usually a 0W-20, as especially suitable for the B38, and MINI used 0W-20 in its own service action. Confirm the approval in your owner's manual, because some manuals also list LL-01 FE or LL-14 FE+.
Does the B38 have a timing belt or chain?
A chain, located at the transmission end of the engine. The oil pump has its own separate chain.
Sources
- BMW Technical Training (via Internet Archive): B46 Engine reference manual, covering the B38 and B46
- BMW Technical Training (via Internet Archive): I12 (i8) powertrain, B38 Top engine
- BMW Group: The new MINI (January 2014 press kit)
- BMW Group: The all-new BMW X1 and the first-ever BMW iX1
- NHTSA / MINI: SI M11 13 16, Service Action: B38 Engine, Check and Replace Crankshaft Guide Bearing
- NHTSA: Recall 18V465000, crankshaft sensor firmware
- BimmerToday: BMW three-cylinder long-term test, problems with the B38
- BimmerToday: From July 2018, gasoline particulate filters for all BMW gasoline engines in Europe
- Auto Świat: BMW/MINI 1.5T B38 engine, faults, technology and running costs
- BMWBlog: BMW B38 engine reliability, efficiency and tuning
- BMWBlog: 2019 BMW 1 Series (F40) engine line-up
- BMWBlog: 2017 MINI Cooper S E Countryman ALL4 plug-in hybrid
- What Car?: BMW 2 Series Active Tourer revealed
- Motul: 8100 Eco-clean 0W-20 technical data sheet (BMW LL-17 FE+)
- UnixNerd: BMW B38 three-cylinder turbocharged engines
- Wikipedia: BMW B38 engine (application list)
Keep reading
Related posts

Engine Guides
BMW N55 Engine Guide: Specs, Problems and Buying Advice
BMW N55 3.0 turbo six explained: verified specs by model, the VANOS recall, common leaks and water pump faults, N54 differences and a used-car checklist.
BMW11 min

Engine Guides
BMW S58 Engine Guide: Specs, Problems and Buying Advice
BMW S58 explained: specs and power for each M3, M4, M2 and X3 M, the bearing-shell campaigns, M Ignite, and what to check before buying a used one.
BMW12 minVideo

Engine Guides
BMW B47 Diesel Guide: Specs, EGR Recall and Problems
BMW B47 2.0 diesel explained: verified specs by model, the EGR cooler recall and its scope, damper and DPF issues, and a used-buyer checklist.
BMW12 minVideo

Engine Guides
BMW B58 Engine Guide: Specs, Problems and Buying Advice
BMW B58 3.0 turbo six explained: specs by version (B58, TU, TU2), the Supra link, known problems backed by BMW bulletins, and used-buyer checks.
BMW14 minVideo

Engine Guides
BMW M54 Engine Guide: Specs, Problems and Buying Checks
BMW M54 2.2, 2.5 and 3.0 specs by market, where it was fitted, CCV, cold-climate and cooling problems with BMW bulletins, and a used-car checklist.
BMW10 minVideo

Engine Guides
BMW N20 and N26 Engine Guide: Specs, Chain Issue, Buying
BMW N20/N26 specs by version, the timing and oil pump chain problem with BMW's 7/70 extension and Gelis settlement, recalls, and a used-car checklist.
BMW13 minVideo

Lights on.
Subscribe.
Engine walkthroughs for BMW, VW, Audi and Mercedes-Benz owners, on YouTube at @HarisCars.
Subscribe on YouTube