Engine Guides · BMW
BMW B47 Diesel Guide: Specs, EGR Recall and Problems
BMW B47 2.0 diesel explained: verified specs by model, the EGR cooler recall and its scope, damper and DPF issues, and a used-buyer checklist.
12 minVideo walkthroughBy Haris Cars
The BMW B47 is a 2.0-liter, four-cylinder turbodiesel that BMW introduced in 2014 as the successor to the N47, and it has powered everything from the 118d and 320d to the X3, 520d and diesel Minis. It is an efficient, strong-pulling engine that suits drivers who cover real highway miles. The main watch-outs are the EGR cooler, which is covered by a long-running BMW recall, the crankshaft vibration damper, and a particulate filter that does not tolerate a diet of short trips.
Haris walks through the engine in the video above. This guide is the written reference, with a source behind every number. One note for US readers before you go further: BMW's US diesels from this era, such as the 328d, used the older N47, so check which engine you actually have.
BMW B47 at a glance
The B47 is a 1,995 cc inline-four diesel with an all-aluminum construction and a chain-driven valvetrain, built in single-turbo and twin-turbo forms.
- Layout: inline four-cylinder, four valves per cylinder, double overhead camshafts.
- Displacement: 1,995 cc (2.0 liters).
- Bore × stroke: 84 mm × 90 mm.
- Construction: aluminum. BMW's 2014 X4 launch release describes the new 2.0-liter diesel as "all-aluminium".
- Injection: common-rail direct injection.
- Induction: one turbocharger on early versions. After the 2018 technical update, BMW says every four-cylinder diesel uses two turbochargers.
- Timing drive: chain, mounted at the transmission end of the engine.
- Codes you'll see: B47D20 for longitudinal (rear-drive and xDrive) cars and B47C20 for transverse (front-drive) cars. Tooling makers list suffixes such as B47 D20A, D20B, C20A and C20B.
- Years: 2014 to the present.
Power and torque depend on the car and the year, so here are the figures from BMW's own launch material and one trade report:
- 218d Active Tourer (2014, transverse): 110 kW (150 hp) and 330 Nm, per BMW's launch release.
- X4 xDrive20d (2014): 190 hp at 4,000 rpm and 400 Nm, per BMW's X4 launch release.
- 320d EfficientDynamics Edition (2015): 120 kW (163 hp), per BMW's 3 Series update release.
- 18d and 20d after the 2017–18 update (B47TÜ1): 110 kW (150 hp) with 350 Nm, and 140 kW (190 hp) with 400 Nm, as reported by BMW Blog.
- 320d (2022 3 Series update): 190 hp and 400 Nm, with a 48-volt mild-hybrid system that can add 11 hp of electric boost, per BMW.
Where you'll find the B47
The B47 went into almost every four-cylinder diesel BMW and Mini sold outside North America from 2014 onward.
The longitudinal B47D20 appears in the 1, 2, 3, 4 and 5 Series as 18d, 20d and 25d models, in the X3, X4 and X5, and in 6 Series GT and 7 Series 725d variants. The transverse B47C20 went into the front-drive platform: the 2 Series Active Tourer and Gran Tourer, X1, X2 and Mini Cooper D and Cooper SD models. BMW Blog reported the 150 hp and 190 hp stages arriving in the 2 Series Active Tourer in 2014 and expected them to follow in Minis and xDrive models.
US buyers: BMW of North America's injector warranty bulletin lists the 2015–2017 328d sedan and wagon with the N47T engine, and the X5 xDrive35d and 535d with the six-cylinder N57T. If you own a US-market diesel BMW, our N47 guide is likely the one you need. Not sure? Our guide to finding your exact engine code shows where to look.
Versions and revisions
The B47 has had three broad phases: the 2014 launch engine, the 2017–18 technical update known as B47TÜ1, and 48-volt mild-hybrid versions from around 2020.
2014–2017: launch engine
BMW launched the B47 as part of a modular engine family it shared with the B37 three-cylinder diesel and the B38 and B48 gasoline engines. BMW's 2016 3 Series Gran Turismo release says the four-cylinder diesels from this family arrived in the 3 Series with the "engine generation" introduced in summer 2015. Launch versions mostly used a single turbocharger. The 25d models were already twin-turbo.
2017–2018: B47TÜ1
The first technical update made two-stage turbocharging standard. BMW Blog describes it as a small variable-geometry turbo working at low load, with a larger fixed-geometry turbo taking over at higher load. Injection pressures went up, liner and piston surfaces were revised, and the engine was prepared for Euro 6c, WLTP and real-driving emissions tests. BMW's January 2018 release for the 2 Series Active Tourer confirms both changes. From March 2018, all its diesels got a particulate filter, a NOx storage catalyst and an SCR system, and "all four-cylinder diesels now feature" two turbochargers. SCR is the system that uses AdBlue (DEF).
2020 on: 48-volt mild hybrid
Later 320d and 520d models pair the B47 with a 48-volt starter-generator. In BMW's 2022 3 Series release, the 320d is listed at 190 hp and 400 Nm, and the starter-generator can add an extra 11 hp when you pull away. The battery is charged through brake energy regeneration.
Known problems
The documented B47 problems are the EGR cooler (recalled), the crankshaft vibration damper (a BMW service bulletin), and emissions hardware that suffers from short-trip use. We found no BMW recall or bulletin on B47 timing chains.
EGR cooler coolant leak (recall)
What happens: BMW says glycol coolant can leak inside the EGR cooler. The coolant mixes with normal soot deposits, and at the high temperatures inside the EGR module this can produce smoldering particles. In rare cases the intake manifold melts, and in very rare cases there can be a fire.
Symptoms: BMW's US recall filing lists a low-coolant warning, reduced engine power, an unpleasant exhaust smell, an unusual noise from the engine bay, and smoke from the engine compartment.
Scope: This campaign has grown in waves, and it is defined by model and build date rather than by engine code:
- 2018, Korea and Europe: after a run of engine fires in South Korea, BMW recalled about 480,000 diesels in Europe and Asia in August 2018. In October 2018 it widened the action to about 1.6 million four- and six-cylinder diesels built between August 2010 and August 2017.
- UK: 268,000 cars were included in 2018, and another 27,000 were added in October 2019. Which?'s list of affected UK models runs from the 1 Series to the X6, with build windows ending as late as September 2017 (1 Series), November 2017 (3 Series) and December 2017 (2 and 5 Series). Those windows include early B47 cars as well as N47 and six-cylinder models.
- Germany (KBA): Auto Motor und Sport reports that the KBA has tracked the recall under reference number 008124 since November 18, 2019. A 2020 extension covered four-cylinder diesels built between April 2015 and September 2016 (the B47's early years), and the existing cooler was replaced with a part from a different supplier. A later wave added about 298,500 cars from almost every diesel model line, built in 2021 and 2022. Auto Motor und Sport puts the worldwide total at about 1.9 million BMW diesels built from 2010 to 2022.
- US (NHTSA): recall 21V-907 covers 50,404 cars: the 2013–2018 328d, 2014–2018 328d Sports Wagon, 2014–2016 535d, 2015 740Ld xDrive, 2015–2017 X3 xDrive28d and 2014–2017 X5 xDrive35d. Recall 25V-700, filed in October 2025, adds 112 model-year 2018 328d sedans and wagons built in late 2018 that were missed the first time. BMW's consumer advisory for 25V-700 is "Do Not Drive" and "Park Outside". These are N47 and N57 cars, not B47s.
Fix: in BMW's US remedy, the EGR cooler is replaced, the intake manifold is inspected and replaced if needed, and the EGR pipe to the manifold is cleaned. BMW Blog reports that an improved cooler from a different supplier has been used in production since 2022.
How to check: run the VIN through BMW's recall lookup or your national checker. In the UK that's the DVSA service at check-vehicle-recalls.service.gov.uk, and in the US it's nhtsa.gov/recalls. Ask for paperwork showing the recall was done. A car whose coolant needs regular top-ups with no visible leak should be checked for this first.
Crankshaft vibration damper separating
What happens: BMW service bulletin SI B11 01 19 covers B4x and B5x engines (with a MINI version, SI M11 01 19, for B3x and B4x engines). It says the rubber insulator between the drive-belt pulley and its center hub can partly or fully tear. The pulley and hub then move independently, and the drive belt can be damaged.
Symptoms: rough running, vibration, or a grinding noise from the engine bay. Because the belt drives the alternator and water pump, you may also see "Vehicle battery is not being charged" or engine-temperature warnings. The bulletin lists fault code 2A1100 (alternator, mechanical fault) for diesels.
Fix and confirmation: remove the drive belt and look for cracks in the damper's rubber. If it is cracked, or the hub and pulley are no longer bonded, BMW replaces the damper and belt, then spins each belt-driven pulley by hand to check for roughness or play.
DPF blockage from short trips
A B47 that only does short runs can fill its diesel particulate filter faster than it can clean it. The AA says active regeneration typically happens every 300 miles or so and needs a sustained drive. A fuel level below about a quarter of a tank can stop it. Repeated failed regenerations end with a warning light and reduced power. Our DPF regeneration guide covers BMW's own regeneration logic, fault codes and the legal position on deletes.
AdBlue (SCR) faults on later cars
Cars built after the 2018 update use AdBlue injection, so they can show the usual SCR warnings, including the countdown to a no-start condition. Faults range from a low tank to sensor and heater problems. Our AdBlue warnings guide explains what each message means and BMW's bulletins on them.
Timing chain
The B47's chain sits at the gearbox end of the engine. Tool maker BGS's instructions for B37 and B47 timing tools state that the engine must come out, and the flywheel must be removed, to change the chain. That makes it a big job if it is ever needed. We could not find a BMW bulletin, recall or warranty extension for B47 timing chains. Treat any rattle from the back of the engine as a reason to get a specialist's diagnosis before you buy, not as a known pattern.
Buying checklist for a used B47
Start a B47 inspection with the paperwork: recall status, service history and oil spec tell you more than a test drive.
- Confirm the engine: check the engine code and whether the car is pre- or post-2018 (single or twin turbo, with or without AdBlue).
- Recall status: check the VIN for the EGR cooler recall and ask for proof that the work was done. Some cars have been recalled more than once.
- Coolant: look at the coolant level when cold, and ask whether it needs regular top-ups.
- Scan it: read the engine fault memory, not just the dashboard. Look for DPF load or backpressure codes, SCR or NOx sensor faults, and 2A1100. Our OBD-II buying guide covers what a basic scanner can and can't see on a BMW.
- Usage pattern: a low-mileage diesel that only did school runs is a DPF risk. Ask how it was driven.
- Belt drive: with the engine idling, listen for grinding or a wobbling pulley at the front of the engine.
- Cold start: listen for rattles from the rear of the engine in the first seconds after a cold start.
- Smoke and smell: visible smoke from a DPF-equipped car, or a coolant or burning smell from the engine bay, is a walk-away sign until it is diagnosed.
- Oil records: check the invoices for a BMW Longlife approval that suits a particulate-filter diesel (see below).
Maintenance that matters
The best thing you can do for a B47 is use the right low-ash oil, keep to the service schedule, and give it regular long drives.
- Oil: a diesel with a particulate filter needs a low-ash BMW approval. Motul's LL-04 data sheet says an LL-04 oil must be used in particulate-filter diesels whatever the country. LL-12 FE (a 0W-30) is approved in Europe only, for diesels certified for it from model year 2014 with no more than one turbocharger, so not for twin-turbo engines. Our BMW Longlife oil guide explains which approval fits which engine.
- Service intervals: follow the car's service indicator and your owner's manual. If the car does lots of short trips or you plan to keep it a long time, changing the oil before the indicator asks for it does no harm.
- Driving pattern: a sustained highway run every week or two lets the DPF regenerate fully. Don't switch off in the middle of a regeneration if you can avoid it.
- Coolant: keep an eye on the level. On this engine, unexplained coolant loss points to the EGR cooler before anything else.
- AdBlue: on post-2018 cars, refill it well before the range countdown runs low.
The B47 at high mileage
A B47 with complete records, finished recalls and a highway-heavy history is a reasonable high-mileage buy. One with gaps in its history is a gamble on its emissions hardware.
We are not aware of any credible published failure rate for B47s by mileage, and we won't invent one. Here is what is documented. The EGR cooler has been recalled more than once, the vibration damper has a BMW bulletin, and the DPF and SCR hardware wears faster under short-trip use. The rear-mounted timing chain is the one big-ticket item that would need the engine removed, so a quiet engine on a cold start matters more on a 150,000-mile car than on a young one.
Budget for the emissions parts rather than the core engine. On a high-mileage example, assume that a DPF, a NOx sensor or an AdBlue component may need replacing at some point, and price the car to allow for it.
Frequently asked questions
Is the BMW B47 a reliable engine?
Its documented weak points are specific rather than widespread. They are the EGR cooler (recalled), the crankshaft vibration damper (covered by a BMW bulletin), and DPF or AdBlue faults on cars used for short trips. A B47 with its recalls done and a good service history is a sensible used buy.
Does the B47 have the N47's timing chain problem?
The B47's chain is at the back of the engine, and changing it means removing the engine. But we found no BMW recall, bulletin or warranty extension for B47 timing chains. Listen for rattles on a cold start and check the service history.
Is my BMW affected by the EGR cooler recall?
The recall is defined by model and build date, not by engine code. Diesel BMWs built from 2010 to 2017 are widely covered, and later waves include 2021–2022 builds. Enter your VIN in BMW's recall lookup, the DVSA checker in the UK or nhtsa.gov in the US.
What oil does a BMW B47 need?
A low-ash BMW Longlife approval for particulate-filter diesels. LL-04 is approved in all markets. In Europe, single-turbo B47s certified for it can also use LL-12 FE, but twin-turbo engines can't. Your owner's manual has the final word.
Was the B47 sold in the US?
BMW's US diesel 3 Series used the N47T through the 2017 model year, according to BMW of North America's own bulletin. The B47 was built for Europe and other markets. If you're shopping in the US, assume a four-cylinder BMW diesel is an N47 until the engine code proves otherwise.
Sources
- BMW Group Newsroom: The new BMW X4 (March 2014)
- BMW Group Newsroom: The new BMW 2 Series Active Tourer (2014)
- BMW Group Newsroom: The new BMW 3 Series Sedan and Touring (May 2015)
- BMW Group Newsroom: Der neue BMW 3er Gran Turismo (June 2016)
- BMW Group Newsroom: The new BMW 2 Series Active Tourer and Gran Tourer (January 2018)
- BMW Group Newsroom: The new BMW 3 Series Saloon and Touring (May 2022)
- BMW Blog: BMW modular engines B37, B38, B47 and B48
- BMW Blog: Four-cylinder BMW diesels get their first big update
- BMW Blog: EGR cooler recall affecting 800,000 diesel engines
- Wikipedia: BMW B47
- BGS technic: Engine timing tool set 6775 for BMW B37/B47 diesels (instructions)
- NHTSA: Part 573 Safety Recall Report 21V-907 (BMW EGR cooler)
- NHTSA: Part 573 Safety Recall Report 25V-700 (BMW EGR cooler)
- BMW of North America via NHTSA: SI B01 09 19, N47T/N57T diesel fuel injectors warranty extension
- BMW of North America via NHTSA: SI B11 01 19, Engine vibrations or noise (vibration damper)
- BMW of North America via NHTSA: SI M11 01 19, Engine vibrations or noise (MINI)
- Auto Motor und Sport: BMW-AGR-Rückruf, Brandgefahr bei weiteren 300.000 Autos
- Auto Bild: BMW Diesel-Motorbrände und Rückrufe
- Motoring Research: Massive BMW diesel engine recall is expanded
- Which?: BMW extends UK recall over fire risk
- The AA: Diesel particulate filters
- Motul: Specific LL-04 5W-40 data sheet
- Motul: Specific LL-12 FE 0W-30 data sheet
Keep reading
Related posts

Maintenance & Problems
DPF Regeneration Explained: TDI, B47/N47, OM651 and OM654
How DPF regeneration works on VW/Audi TDI, BMW N47/B47 and Mercedes OM651/OM654: warning lights, oil dilution, forced regens, cleaning and delete law.
10 min

Engine Guides
BMW N47 Diesel Guide: Timing Chain, Recalls and Buying
BMW N47 2.0 diesel: specs by model, which engines the timing chain campaign covered, N47 vs N47T, EGR and fuel pump recalls, and a used-car checklist.
BMW12 minVideo

Engine Guides
BMW N55 Engine Guide: Specs, Problems and Buying Advice
BMW N55 3.0 turbo six explained: verified specs by model, the VANOS recall, common leaks and water pump faults, N54 differences and a used-car checklist.
BMW11 min

Engine Guides
BMW S58 Engine Guide: Specs, Problems and Buying Advice
BMW S58 explained: specs and power for each M3, M4, M2 and X3 M, the bearing-shell campaigns, M Ignite, and what to check before buying a used one.
BMW12 minVideo

Engine Guides
BMW B38 Engine Guide: Specs, Problems and Buying Advice
BMW and MINI B38 1.5 three-cylinder: verified specs by model, the 2015 thrust bearing fix, leaks, recalls, oil spec and a used-car checklist.
BMW12 minVideo

Engine Guides
BMW B58 Engine Guide: Specs, Problems and Buying Advice
BMW B58 3.0 turbo six explained: specs by version (B58, TU, TU2), the Supra link, known problems backed by BMW bulletins, and used-buyer checks.
BMW14 minVideo

Lights on.
Subscribe.
Engine walkthroughs for BMW, VW, Audi and Mercedes-Benz owners, on YouTube at @HarisCars.
Subscribe on YouTube