Skip to content

Engine Guides · BMW

BMW B58 Engine Guide: Specs, Problems and Buying Advice

BMW B58 3.0 turbo six explained: specs by version (B58, TU, TU2), the Supra link, known problems backed by BMW bulletins, and used-buyer checks.

14 minVideo walkthroughBy Haris Cars

Video walkthrough of this post.Open on YouTube

The B58 is BMW's 3.0-liter turbocharged inline-six, introduced in 2015 to replace the N55. It powers everything from the 340i and M340i to the X5 xDrive40i, 740i and the Toyota GR Supra. It is one of the better modern BMW engines to own. The common faults are leaks and wear parts, not design flaws in the bottom end: the crankcase pressure control valve on early cars, coolant leaks around the oil filter housing and cooling system, and a few well-documented service bulletins.

Haris walks through the engine in the video above. This guide is the written reference, with a source for every specific claim.

B58 at a glance

The B58 is a 2,998 cc aluminum inline-six with a closed-deck block, one twin-scroll turbo, direct injection and BMW's Valvetronic and double-VANOS valve control. The figures below come from BMW's 2015 training manual unless noted.

  • Displacement: 2,998 cc
  • Bore × stroke: 82.0 × 94.6 mm
  • Compression ratio: 11.0:1 at launch. Toyota lowered it to 10.2:1 in the 2021 GR Supra.
  • Block: closed-deck aluminum crankcase with electric-arc wire-sprayed cylinder walls, so there are no separate liners
  • Crankshaft: forged steel
  • Cylinder head and valvetrain: aluminum head with Valvetronic variable intake valve lift and double VANOS cam timing
  • Induction: single twin-scroll turbocharger with an electric wastegate. A water-to-air charge air cooler is built into the intake plenum.
  • Injection: direct injection at up to 200 bar on the original engine and 350 bar from the 2018 technical update. The TU2 version adds a low-pressure injection stage.
  • Timing drive: chain, at the transmission end of the engine
  • Introduced: 2015, first in the 340i

Power and torque depend on the model and the revision, so treat these as examples, not one universal figure:

  • 2016 340i (US, B58 original): 240 kW (320 hp) at 5,200 to 6,500 rpm; 450 Nm (330 lb-ft) from 1,380 rpm (BMW training manual)
  • 2019 X5 xDrive40i (B58TU): 250 kW (335 hp); 450 Nm (330 lb-ft) (BMW B58TU training manual)
  • 2020 M340i (US): 382 hp at 5,800 to 6,500 rpm; 369 lb-ft at 1,800 to 5,000 rpm (BMW USA press release)
  • 2020 Toyota GR Supra 3.0: 335 hp; 365 lb-ft (Toyota)
  • 2021 Toyota GR Supra 3.0: 382 hp; 368 lb-ft (Toyota)
  • Facelifted X7 xDrive40i, 2022 launch (B58TU2): 280 kW (380 hp in BMW's global release); 520 Nm, or 540 Nm briefly with the 48-volt boost (BMW)
  • 2023 740i (US, B58TU2): 375 hp; 383 lb-ft, or 398 lb-ft briefly with the mild-hybrid boost (BMW USA)

Where you'll find the B58

The B58 went into almost every BMW badged 40i or M40i from 2016 on, plus the Toyota GR Supra. Check the exact engine code on your car before buying parts, because the three revisions don't share every component.

Original B58 (2016 to about 2019 model years)

BMW's 2023 warranty-extension bulletin for the crankcase valve lists the US cars with this engine and their production windows:

  • 3 Series: 340i and 340i xDrive sedan (F30), built June 2015 to October 2018; 340i xDrive Gran Turismo (F34)
  • 2 Series: M240i coupe and convertible, 2017 to 2021 model years
  • 4 Series: 440i coupe, convertible and Gran Coupe (F32/F33/F36), 2017 to 2020
  • 5, 6 and 7 Series: 540i (G30), 640i xDrive Gran Turismo (G32), 740i/740Li (G12)
  • X3 and X4: X3 M40i (G01) built July 2017 to July 2019; 2019 X4 M40i (G02)

B58TU (from mid-2018)

  • First applications: X5 xDrive40i (G05) from July 2018 and X7 xDrive40i (G07) from December 2018, according to BMW's B58TU training manual
  • 3 Series: the 2020 M340i (G20) launched with the TU's 350-bar injection and a twin-scroll turbo with an integrated steel exhaust manifold

B58TU2 (from 2022)

  • First application: the facelifted X7 xDrive40i, with market launch from August 2022
  • Also: the 2023 740i (G70), which BMW USA's press kit names as the first B58TU2 car in the 7 Series

Toyota GR Supra (A90)

The fifth-generation Supra, built by Magna Steyr in Graz, Austria, uses the B58. Toyota's own press kits don't name BMW, but the engine dimensions match (82 × 94.6 mm, 11.0:1 at launch). HP Academy lists the A90 Supra as a B58 application, and BMW of North America ran recall 21V598000 on 2020 and 2021 Supras alongside B58 BMWs.

  • 2020 model year: 335 hp and 365 lb-ft, eight-speed automatic
  • 2021 model year: 382 hp and 368 lb-ft. Toyota fitted a dual-branch exhaust manifold with six ports instead of two, and new pistons that lowered compression from 11:1 to 10.2:1.
  • 2023 model year: a six-speed manual became optional on the 3.0 and 3.0 Premium
  • End of production: Toyota said the last Supra would leave the line in March 2026, as reported by Carscoops. The Z4 also ends in 2026.

Versions and revisions: B58, TU and TU2

BMW has revised the B58 twice: the B58TU in 2018 and the B58TU2 in 2022. Both updates raised output and changed parts that matter for repairs. BMW's documents use suffixes such as B58B30M0, M1 and M2 for these revisions. In service bulletins, "B58M" and "B58C" mark different variants.

Original B58 (B58B30M0, 2015)

The first B58 shared its modular design with BMW's B48 four-cylinder and B47/B57 diesels. BMW's training manual highlights the closed-deck block, the twin-scroll turbo cast as one piece with part of the exhaust manifold, the charge air cooler inside the intake plenum, a map-controlled oil pump, a mechanical coolant pump and an electrically actuated heat management module. The two-part timing chain sits at the transmission end, where BMW says the gearbox's inertia reduces the loads on the chain.

B58TU (B58B30M1, 2018)

The technical update arrived with the 2019 X5. BMW's B58TU training manual and the M340i launch material list these main changes:

  • Injection pressure: raised from 200 to 350 bar, with new injectors and a new high-pressure pump
  • Cylinder head: the medium-power version has the exhaust manifold integrated into the aluminum head. Higher-power versions keep a separate manifold.
  • Timing drive: the two-part chain was replaced by a single chain
  • Cooling: split cooling with an electric split-cooling valve, working with the heat management module
  • Turbo: on the M340i, BMW quotes a twin-scroll turbo with an integrated steel exhaust manifold and impellers about 25% lighter

B58TU2 (B58B30M2, 2022)

The second update brought a Miller-cycle combustion process and dual injection. BMW's 7 Series press kit says that "some of the fuel is now injected into the combustion chambers via a low-pressure system", in addition to the high-pressure direct injectors. That makes it the first B58 with port-style injection, which should reduce intake-valve carbon. BMW also lists:

  • VANOS: electrically operated cam timing
  • Exhaust rockers: switchable exhaust-side rocker arms that can shut down gas exchange on overrun, cutting overrun friction by about two-thirds
  • Ignition: an active coil with integrated electronics
  • Cylinder head: integrated exhaust manifold
  • 48-volt mild hybrid: a starter-generator integrated into the transmission

Known B58 problems

The B58's documented problems are mostly leaks and ancillaries. We found BMW bulletins for the crankcase valve, an early turbo oil leak, two cooling-system faults and a coolant-pump pulley. Owner and parts-retailer reports add the oil filter housing, heat management module and water pump. Run any car's VIN through NHTSA and a BMW dealer for open campaigns before you buy.

Crankcase pressure control valve (PCV) on early cars

The PCV valve sits in the cylinder head cover. BMW of North America extended its warranty to 15 years or 150,000 miles on US-spec original B58 cars (SIB 01 14 23, November 2023).

  • Symptoms: blue or white smoke after a cold start, a high-pitched whistle at idle, misfire codes 140601 or 140610 for cylinder 6, shuddering or reduced power
  • Cause: the valve's rubber diaphragm can rupture and stop separating oil from the blow-by gases
  • How to confirm: BMW's crankcase pressure test. BMW gives about -100 mbar of vacuum, instead of about -50 mbar, as an example of a faulty valve.
  • Fix: BMW's repair kit for the B58 pressure control valve
  • Coverage: the cars listed above, US-registered only. The bulletin excludes cars operated and repaired outside the US. UK and EU owners should ask a BMW dealer what applies locally.

FCP Euro, a BMW parts retailer, says this failure has not become a significant issue on the B58TU.

Oil filter housing and coolant leaks

The B58's plastic oil filter module contains the oil-to-coolant heat exchanger, so a failing housing can leak oil, coolant or both. We found no BMW bulletin for this on the B58, but parts retailers and owners report it widely.

  • Symptoms: coolant leaking toward the rear of the engine, low coolant or low oil warnings
  • Cause: FCP Euro says the housing gaskets flatten and the plastic warps with heat, typically around 60,000 to 100,000 miles. Over-tightening the filter cap can also crack it.
  • Fix: new gaskets or a new housing
  • Legal status: a proposed class action filed in New Jersey federal court, Eiger v. BMW of North America, names B46, B48 and B58 engines. The plaintiffs allege replacements cost $1,500 to $4,000. These are allegations, not findings.

Note the scope of BMW's own bulletin. SIB 11 10 25 (December 2025) addresses coolant leaking from the oil filter housing, but it covers only the B46, B48 and plug-in-hybrid four-cylinders, not the B58.

Other cooling-system leaks

BMW has issued three B58 cooling bulletins, and owners report a few more weak points:

  • Low-temperature coolant gassing (SIB 17 02 20): X5, X6 and X7 with the B58C built up to August 26, 2019. Coolant leaks under the car or pressure escapes when opening the low-temperature reservoir. The DME may store 20A201 (charge air cooling coolant pump dry-running protection). BMW blames premature breakdown of the coolant. The fix is two drain-and-refills with BMW coolant.
  • Heater hose rubbed by the steering shaft (SIB 17 01 18): 740Li, 540i and 640i xDrive Gran Turismo with the B58. Symptoms are a coolant leak at the front, a low-coolant warning or a noise when turning. The fix is a hose bracket, plus a new hose if it's already worn through.
  • Coolant pump pulley (SIB 11 05 21, service action): G05, G06, G07, G20, G22, G23 and G30 cars built from September 2020 to May 24, 2021. The pulley on the mechanical pump may fracture, letting the drive belt come off the coolant pump and alternator. The fix is a new pump.
  • Heat management module (owner-reported): FCP Euro reports leaks from this plastic thermostat module as early as 40,000 miles, with split-cooling or cooling-system fault codes.
  • Mechanical water pump (owner-reported): FCP Euro reports shaft-seal leaks around 100,000 to 120,000 miles, seen as coolant streaks under the car.

Turbocharger oil leak on early cars

BMW's SIB B11 15 16 covers B58M engines built up to September 2017 in the 2, 3, 4, 5, 6 and 7 Series. Oil shows at the bottom of the turbo near the band clamp, and the cause is a loose clamp. The fix is to retighten it. BMW notes that if that doesn't stop the leak, the complete turbocharger has to be replaced.

Oil filter element breaking apart

BMW bulletins SIB 11 01 20 and 11 03 21 cover all B58 variants. On rare occasions the genuine filter insert is hard to remove or tears, leaving the lower plastic section stuck in the housing. BMW published a removal procedure and an oil-catch tool. DIY owners should follow the procedure rather than forcing the cap.

Oil pump (retailer-reported)

FCP Euro says BMW used a plastic carrier in the oil pump until 2020 production and that thicker oils such as 5W-40 strain it. It links the problem to fault codes 1C2002 and 1FB801. We found no BMW bulletin confirming this. The practical takeaway is simple: use the viscosity BMW specifies.

Recall 21V598000: brake assist after start

This NHTSA recall covers 2020 M340i, 540i and X3 M40i, 2020 to 2021 X4 M40i and 745Le, 2019 to 2021 Z4 M40i and 2020 to 2021 Toyota Supra. Engine management software could cause a loss of brake assist during engine start. Dealers update the software free of charge.

Carbon buildup

The original B58 and the B58TU are direct injection only, so the backs of the intake valves never get washed by fuel. The B58TU2's added low-pressure injection reduces that risk. We explain the mechanism and cleaning methods in our carbon buildup guide.

Buying checklist for a used B58

Buy on condition and paperwork. These checks take an hour and catch most of the expensive surprises:

  • Open campaigns: run the VIN on nhtsa.gov and ask a BMW dealer to check open service actions and the PCV warranty-extension note (SIB 01 14 23) on early US cars.
  • Cold start: listen for a whistle at idle and look for blue or white smoke. Both point to the PCV valve.
  • Fault codes: scan the engine module for stored codes, including history codes. Misfires on cylinder 6 (140601, 140610) and 20A201 deserve questions. Our OBD-II pre-purchase guide explains what a generic scanner can and can't see.
  • Coolant: check both the main and low-temperature reservoirs when cold. Look for dried coolant residue at the rear of the engine, under the oil filter housing and on the underbody.
  • Oil leaks: look at the valve cover, the turbo oil lines and the bottom of the turbo on pre-September 2017 cars.
  • Service records: look for regular oil changes with BMW-approved oil, and for receipts for the oil filter housing gaskets, water pump or heat management module if the car is past 60,000 miles.
  • Tuning: ask whether the DME has been tuned or flashed back to stock, and check for aftermarket intakes, downpipes or charge pipes. The B58 is popular with tuners, and history matters.
  • Supra buyers: confirm recall 21V598000 was done on 2020 to 2021 cars.

Maintenance that matters

Correct oil, clean coolant and leak checks keep a B58 healthy. Most known failures announce themselves with a leak or a warning before they become expensive.

  • Oil spec: use the BMW Longlife approval and viscosity for your exact car. BMW's 2015 B58 training manual lists Longlife-01 and Longlife-04. A 2023 X7 manual lists Longlife-01 FE, Longlife-17 FE+ and Longlife-22 FE++, in 0W-12, 0W-20 or 0W-30, with the correct grade on a label under the hood. Our BMW Longlife oil guide explains which approval applies where, including the EU-only rules.
  • Oil change interval: follow the service interval the car displays as the maximum. Many enthusiasts change oil sooner, especially on tuned or tracked cars. That's a reasonable choice, but it isn't a BMW requirement.
  • Coolant: BMW's cooling bulletins specify BMW-approved coolant. Don't top up with a generic mix.
  • Spark plugs and coils: FCP Euro puts typical plug life around 80,000 miles. Check your service schedule, and replace plugs sooner on tuned cars.
  • Timing chain: it sits at the transmission end, so any chain work is a big job. Clean oil at the right level is the best protection. We cover chain vs belt tradeoffs in our timing chain guide.

The B58 at high mileage

A well-maintained B58 is a reasonable high-mileage purchase. Its documented weak points are bolt-on parts, not cranks, bearings or the block. The engine has a closed-deck block, a forged crank and a chain drive at the rear. BMW's bulletins concern valves, hoses, clamps, coolant and software rather than internal failures.

Be realistic about running costs, though. FCP Euro's mileage ranges put the oil filter housing, heat management module and water pump all inside the first 120,000 miles. On early US cars the PCV warranty extension ends at 150,000 miles or 15 years. Budget for the oil filter housing gaskets, water pump, heat management module, plugs and coils if the records don't show them done. A car with patchy records and a modified DME carries more risk than an untouched one at higher mileage.

If you are weighing a B58 against its predecessor, our planned N55 engine guide covers the engine it replaced. The S58 guide covers the M version built from the B58TU.

Frequently asked questions

Is the BMW B58 reliable?

Yes, by modern turbo-engine standards. Its documented problems are mostly leaks and ancillary parts: the PCV valve on early cars, cooling-system components and the oil filter housing. We found no BMW bulletin pointing to systematic bottom-end failure.

What is the difference between the B58 and B58TU?

The B58TU (2018) raised injection pressure from 200 to 350 bar, integrated the exhaust manifold into the head on medium-power versions, switched to a single timing chain and added split cooling. The B58TU2 (2022) added Miller-cycle combustion, a low-pressure injection stage, electric VANOS and 48-volt mild hybrid.

Does the Toyota Supra use the BMW B58?

Yes. The A90 GR Supra 3.0 uses the B58. Toyota rated it at 335 hp for 2020 and 382 hp from 2021, when it also lowered compression to 10.2:1 and fitted a new exhaust manifold.

Does the B58 have port injection?

Only the B58TU2, introduced in 2022. BMW describes it as adding a low-pressure injection system to the existing high-pressure direct injection. The original B58 and the B58TU are direct injection only.

What oil does a B58 take?

Use the BMW Longlife approval and SAE grade in your owner's manual and on the engine-bay label. Recent manuals list Longlife-01 FE, Longlife-17 FE+ and Longlife-22 FE++ in 0W-12 to 0W-30, depending on the engine.

Sources

Lights on.
Subscribe.

Engine walkthroughs for BMW, VW, Audi and Mercedes-Benz owners, on YouTube at @HarisCars.

Subscribe on YouTube