Skip to content

Engine Guides · BMW

BMW N52 Engine Guide: Specs, Problems and Buying Advice

BMW N52 inline-six explained: verified specs by version, N52 vs N52KP, lifter tick, VANOS and PCV recalls, oil leaks and a used-car buying checklist.

13 minVideo walkthroughBy Haris Cars

Video walkthrough of this post.Open on YouTube

The BMW N52 is a naturally aspirated 3.0-liter inline-six with port fuel injection, Valvetronic and double VANOS, built around a magnesium-aluminum composite block. BMW introduced it in 2005, and US cars used it through the 2013 model year. It's the simpler, cheaper-to-own alternative to the turbocharged N54. Its known faults are lifter tick, oil leaks, the electric water pump and VANOS and Valvetronic sensor issues. All are well documented, and most are repairs rather than rebuilds. Two safety recalls are worth checking by VIN. It suits buyers who want a smooth six without turbo or direct-injection complexity.

Haris walks through the engine in the video above. This guide is the written reference, with each specification, recall and repair procedure tied to a source.

BMW N52 at a glance

The N52 is a 2,996 cc, DOHC 24-valve inline-six. Its main innovations were the magnesium-aluminum crankcase, Valvetronic II and an electric water pump.

  • Displacement: 2,996 cc
  • Bore × stroke: 85.0 × 88.0 mm
  • Compression ratio: 10.7:1 (N52 and N52KP; the N51 SULEV variant uses lower compression)
  • Valvetrain: DOHC, four valves per cylinder, Valvetronic II variable intake valve lift (0.18 to 9.9 mm) and double VANOS. Hydraulic lifters, chain-driven camshafts.
  • Induction: naturally aspirated, with a three-stage DISA variable-length intake manifold (the original 215 hp "UL" version does without it)
  • Injection: manifold (port) fuel injection
  • Block: two-piece composite crankcase: an aluminum-silicon insert cast inside a magnesium alloy (AJ62) outer shell, with a magnesium bedplate. Alusil cylinder bores, no iron liners.
  • Head: aluminum. The valve cover is magnesium on the original N52 and plastic on the N52KP.
  • Crankshaft: cast iron, seven main bearings
  • Cooling: electric water pump and a map-controlled electronic thermostat
  • Oil pump: volume-controlled
  • Engine management: MSV70 (N52), MSV80 (N52KP)
  • Rev limit: 7,000 rpm
  • Weight: 161 kg, about 10 kg (22 lb) lighter than the M54 it replaced
  • US emissions: ULEV II (N52, N52KP); the N51 is the SULEV II version
  • Years: introduced 2005; in US cars from the 2006 to the 2013 model year

Power and torque by version

BMW sold the N52 at several outputs, using a power-class letter in the engine code. These are BMW's figures from its US technical training material.

  • N52B30 "OL" (2005), e.g. 330i: 190 kW (255 hp) at 6,600 rpm, 300 Nm (221 lb-ft) from 2,500 to 4,000 rpm. In Europe, 190 kW is quoted as 258 PS.
  • N52B30 "UL" (2005), e.g. 325i: 215 hp. This version has no DISA intake system and uses different software and exhaust.
  • N52B30O1 (N52KP high output), e.g. X3 3.0si: 260 hp at 6,600 rpm.
  • N52B30M1 (N52KP medium output), the version in BMW's N52KP data sheet: 172 kW (230 hp) at 6,250 rpm, 270 Nm (199 lb-ft) at 3,000 rpm.
  • N52B30U1 (N52KP low output): 215 hp, listed by BMW in 2006 as a possible future application.

Ratings differed between markets, and later N52T versions had their own figures. For a specific European car, check that market's brochure or registration document.

Which cars have the N52

In the US, the N52 family (N52, N52KP/N52K, N51 and N52T) powered the 25i, 28i and 30i six-cylinder BMWs of roughly 2006 to 2013.

The model list comes from BMW's eccentric-shaft sensor bulletin, which names every N51/N52/N52K/N52T application. The years come from NHTSA recall 22V-119 and recall 14V-176:

  • 1 Series (E82 coupe, E88 convertible): 128i, 2008–2013
  • 3 Series sedan (E90): 325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi, 2006–2011
  • 3 Series Sports Wagon (E91): 2006–2012
  • 3 Series coupe (E92): 328i, 328xi, 328i xDrive, 2007–2013
  • 3 Series convertible (E93): 328i, 2007–2013
  • 5 Series sedan (E60): 525i, 525xi, 528i, 528xi, 530i, 530xi, 2006–2010; Sports Wagon (E61): 530xi, 2006–2007
  • 5 Series (F10): 2011 528i (N52T)
  • X3 (E83): 3.0si and xDrive30i, 2007–2010; X3 (F25): 2011 xDrive28i (N52T)
  • X5 (E70): 3.0si and xDrive30i, 2007–2010
  • Z4 (E85 roadster, E86 coupe, E89 roadster): 3.0i, 3.0si and sDrive30i, 2006–2011

Many of these cars came in several engine versions, and SULEV-state cars may have the N51. Read the engine code before you order parts. Our engine code guide explains how.

Versions and revisions

The N52 had one major update, the N52KP (also written N52K) from September 2006, plus a SULEV variant and a late N52T.

  • N52 (2005): launched in the E60, E61 and E90, first as the 330i and 325i. It came in high-output "OL" and lower-output "UL" versions, with a magnesium valve cover and Siemens MSV70 engine management.
  • Running changes: exhaust valves with stronger 6 mm stems from March 2006 and stiffer connecting rods from June 2006.
  • N52KP / N52K (from September 2006): BMW called it "an improved and cost optimized version". Changes included MSV80 engine management, a digital air-mass meter, a new electronic throttle, a plastic valve cover with an integrated crankcase vent valve and oil separator, stronger connecting rods, 6 mm exhaust valve stems, a second-generation electric water pump and hydroformed camshafts. It first appeared in the 328i Coupe, and BMW said it would eventually replace the N52 in every application.
  • N51 (from September 2006): the SULEV II version for states with stricter rules. It adds a close-coupled catalyst plus an underbody catalyst, a secondary air system, a modified combustion chamber and pistons for lower compression, and stainless steel fuel lines.
  • N52T: the version fitted to the F10 528i and F25 X3 in the 2011 model year. BMW's bulletins treat it as a separate engine code.

The direct-injection, turbocharged N54 arrived alongside the N52KP for 2007. Its crankcase has the same dimensions but is all aluminum. See our N54 guide for that engine.

Known N52 problems

The N52's documented problems are mainly in the valvetrain, sealing and cooling. BMW issued bulletins for each, and two problems led to NHTSA safety recalls.

Lifter tick (hydraulic valve adjusters)

A ticking or rattling from the top of the engine, especially on a cold start, is a known N52 complaint with its own BMW bulletin. BMW's fix is new exhaust-side lifters and rocker arms.

  • Symptoms: per SI B11 09 07 (March 2013), an occasional ticking or rattling from the hydraulic lifters during cold starts or with frequent short trips. In some cases it lasts a long time even when the engine is warm.
  • Which engines: N51, N52 and N52K engines produced up to the end of November 2008, in E60, E61, E70, E82, E83, E85, E86, E88 and E90–E93 cars. BMW phased in improved parts from October 1, 2008.
  • How to confirm: the cylinder head casting number. Improved heads carry 7588277 (N51), 7588273 (N52) or 7588271 (N52K). Cars built in October and November 2008 need the head checked, because the change was staggered.
  • Fix: twelve exhaust hydraulic lifters (P/N 11 33 7 605 330) and twelve exhaust roller rocker arms (P/N 11 33 7 631 589). Only the exhaust camshaft has to come out. BMW withdrew an earlier lifter-bleeding procedure.

VANOS bolt recall and VANOS faults

Later N52 engines are subject to a safety recall for loosening VANOS bolts. All N52 versions can also log VANOS faults caused by poor oil supply.

  • Recall 14V-176 (2014): the bolts securing the VANOS unit housing "can loosen over time and may possibly break", which can cause reduced power or a stall. It covered 156,137 vehicles, including 2010–2011 128i, 328i and Z4 sDrive30i, 2010 X3 xDrive30i and X5 xDrive30i, and 2011 528i and X3 xDrive28i (also N55 cars). Dealers replace the four VANOS housing bolts on both units.
  • Recall 23V-707 (2023): a further 157,796 vehicles from 2010–2012 with the same aluminum VANOS bolt problem, including 1, 3 and 5 Series, X3 xDrive28i/30i, X5 xDrive30i and Z4 sDrive30i.
  • Warranty extension SI B01 10 14: for N51, N52K and N52T cars built from about September 2009 that weren't in the recall, BMW extended the VANOS unit warranty to 10 years with no mileage limit. That's run out on age now.
  • VANOS faults (SI B11 02 08): faults 2A82 or 2A87 ("stiff; jammed mechanically") with reduced power after the engine is fully warm, on N51, N52 and N52K cars built up to January 2010. BMW blames insufficient oil pressure at the adjusters. Its checks are the oil filter cap insert (a missing one lets unfiltered oil reach the solenoids), then both VANOS solenoids with an oil and filter change, then wear on the camshaft bearing ledge.

Because 14V-176 and 23V-707 are NHTSA safety recalls, a VIN check on nhtsa.gov shows whether either is still open.

Eccentric shaft sensor faults (Valvetronic)

Oil leaking past the Valvetronic eccentric shaft sensor gasket can soak the sensor's wiring and even reach the engine computer.

  • Symptoms: rough running, a crank-no-start or a check-engine light, with fault 2A37 or 2A47 (Valvetronic eccentric shaft sensor plausibility). F10 and F25 cars may show 134E08.
  • Cause: per SI B11 06 16, oil leaks at the VVT sensor gasket and contaminates the sensor connector, the engine harness and sometimes the DME connector.
  • How to confirm: unplug the eccentric shaft sensor connector, in the center of the valve cover, and look for oil inside.
  • Fix: sensor, engine harness and valve cover gasket. If oil has reached the DME connector, the DME is replaced too.

PCV valve heater recall (fire risk)

On these cars, the heater in the crankcase ventilation (PCV) valve can short-circuit and overheat. BMW's current remedy is a fused wiring harness.

NHTSA recall 22V-119 (2022) covers 917,106 vehicles and supersedes and expands recalls 17V-683 and 19V-273. Its model list runs from 2006 to 2013 and includes most of the US N52 cars listed above. NHTSA describes the risk as an electrical short that can overheat the heater "increasing the risk of a fire while driving or, soon after driving when parked." Cars repaired under the earlier recalls need to go back for the new remedy, so run the VIN even if the seller says the recall was done.

Oil leaks

The valve cover gasket, oil filter housing and the heat exchanger next to it are the usual leak points, and BMW warns that seepage is often misread as a leak.

BMW's SI B01 04 14 covers the N51, N52, N52K and N52T (along with the N54 and N55). It reports an above-average number of engine gasket claims. Light sweating needs no repair. Medium to large accumulation with pooling, dripping or spotting does. On an N52, an oily valve cover deserves attention for a second reason: the eccentric shaft sensor bulletin traces its faults to oil leaking at the sensor gasket on top of the engine.

Electric water pump and thermostat

The N52 has no belt-driven water pump. An electronically controlled electric pump moves the coolant, and a map-controlled thermostat works alongside it.

BMW's training notes that coolant flowing through the pump cools its motor and lubricates its bearings. A pump that runs dry can seize, and a pump that doesn't start can cause "serious engine damage". When the pump fails, expect a warning and rising temperatures. BMW's coolant pump class-action settlement was mainly for turbo engines, but it also listed one N52K car: the 2007–2010 X5 xDrive30i. Its coverage windows have closed.

N51 only: in-tank fuel hose

On N51 SULEV cars, a fuel hose inside the tank can come loose or split and cut fuel pressure.

SI B12 21 10 covers E82, E88, E90, E92 and E93 cars with the N51 produced up to June 2011. Symptoms are a Service Engine Soon light, loss of power, crank-no-start and misfire or mixture faults. The cause is the rubber hose on the plastic regulator nipple inside the tank. BMW blames tolerance stack-up or deterioration of the hose material.

Warm-up idle hunting

A slightly unstable idle, or a shudder when creeping in D or R during warm-up, is a known software issue on N51, N52K and N52T cars.

SI B12 21 12 covers cars built from June 2006 to November 2012. No faults are stored and the symptoms disappear above 90°C. The fix is improved DME software.

Used N52 buying checklist

Listen to it from cold, scan it, check NHTSA recalls by VIN and look closely at the valve cover area.

  1. Cold start: listen for ticking from the top of the engine. On cars built before December 2008, ask whether the exhaust lifters and rocker arms have been replaced, or check the head casting number.
  2. Open recalls: run the VIN on NHTSA for 22V-119 (PCV heater) and, on 2010–2012 cars, 14V-176 or 23V-707 (VANOS bolts).
  3. Scan for faults: 2A37 or 2A47 (eccentric shaft), 2A82 or 2A87 (VANOS) and any misfire or mixture codes. Our OBD-II buying guide covers what a basic scanner can and can't read on a BMW.
  4. Valve cover area: look for oil around the valve cover gasket, and if possible check the eccentric shaft sensor connector for oil.
  5. Oil filter housing: check the housing and the heat exchanger below it for dripping, not just a damp film.
  6. Cooling: look for receipts for a water pump and thermostat, and watch the temperature after a long drive.
  7. Warm-up behavior: idle hunting during warm-up on an N51 or N52K car points to outdated software, not worn parts.
  8. Major repair history: if the engine has had a head gasket or other major work, ask whether the shop used new aluminum bolts and followed BMW's torque-angle procedure. BMW says the N52's aluminum bolts are single-use.

Maintenance that matters

The N52 asks for correct oil, correct fasteners and coolant handled with care because of the magnesium block.

  • Oil: BMW's N52 technical data lists SAE 5W-30. Use an oil with the BMW Longlife approval your owner's manual specifies. Our BMW Longlife oil guide explains the codes and the US/EU differences.
  • Oil filter cap insert: make sure it's fitted at every oil change. BMW links a missing insert to VANOS solenoid damage.
  • Fasteners: parts bolted to the magnesium block use blue-headed aluminum bolts. BMW says they're single-use and must be torqued with the specified angle procedure. Steel bolts can't be used in the magnesium.
  • Coolant work: during jobs like a head replacement, BMW says bolt holes must be blown dry immediately so coolant can't corrode the magnesium. A damaged head gasket can cause contact corrosion between the aluminum head and the magnesium block "within a relatively short period of time".
  • Water pump: a replacement pump must not run dry. BMW says to store a removed pump full of coolant and to turn the impeller by hand if it has run dry.
  • Timing chain: the N52 uses a timing chain, not a belt. Our timing chain vs belt guide explains what that means for maintenance.

The N52 at high mileage

An N52 with 150,000 miles is a reasonable used-car proposition if its recalls are done and the usual wear items have been dealt with.

The known problems are lifters, VANOS solenoids and bolts, the eccentric shaft sensor, gaskets, the PCV heater and the water pump. All of them are repairs on or around the engine, not rebuilds. BMW's intake-valve carbon cleaning bulletin covers the direct-injected N54, not the port-injected N52.

One real limit is the block itself. BMW's training material says the Alusil cylinder bores "cannot be machined", although the deck can be resurfaced. An N52 with worn bores or a damaged block isn't a candidate for a traditional rebore, so a badly worn or overheated engine usually means a replacement engine or a specialist repair. That makes the cooling system and oil history the most important things to check on a high-mileage car. If you're comparing it with the engine it replaced, see our M54 guide.

Frequently asked questions

Is the BMW N52 a reliable engine?

It's mechanically simpler than BMW's turbocharged sixes: there are no turbochargers and no high-pressure fuel system. Its documented problems (lifter tick, oil leaks, VANOS and eccentric shaft sensor faults, the water pump and the PCV heater recall) are fixable without major engine work. Check for open recalls and look at cooling-system history before buying.

What is the difference between the N52 and N52KP (N52K)?

The N52KP, introduced in September 2006 on the 328i Coupe, is BMW's cost-optimized update of the 2005 N52. It has MSV80 engine management, a plastic valve cover with an integrated crankcase vent valve, a digital air-mass meter, a new throttle, stronger connecting rods and a second-generation electric water pump.

Why does my N52 tick on a cold start?

The most common documented cause is the hydraulic valve lifters on engines built up to November 2008. BMW's fix is twelve new exhaust lifters and twelve exhaust roller rocker arms. Engines with an improved cylinder head casting (7588273 on the N52, 7588271 on the N52K) already have the updated parts.

Does the N52 have a magnesium block?

Partly. The crankcase is an aluminum-silicon insert, which carries the cylinder bores, coolant passages and main bolt threads, cast inside a magnesium alloy outer shell, with a magnesium bedplate. That's why it needs aluminum bolts and careful coolant handling.

Which BMWs have the N52 engine?

In the US: the 2006–2011 325i, 328i and 330i sedans, the 2007–2013 328i coupe and convertible, the 2008–2013 128i, the 2006–2010 525i, 528i and 530i, the 2007–2010 X3 3.0si/xDrive30i and X5 3.0si/xDrive30i, the 2006–2011 Z4 3.0i, 3.0si and sDrive30i, and the 2011 528i and X3 xDrive28i (N52T).

Sources

Lights on.
Subscribe.

Engine walkthroughs for BMW, VW, Audi and Mercedes-Benz owners, on YouTube at @HarisCars.

Subscribe on YouTube